Skip to content
Engineering Bible

Results appear as you type. Use the arrow keys to move through them and Enter to open one.

Popular

↑ ↓ moveEnter openEsc close

Naval architecture and marine engineering practice problems

10 multiple-choice problems in the style of the FE and PE engineering exams. Pick an answer to check it, then open the worked solution. Every answer is recomputed by the maritime calculator that solves it, and the solution opens that calculator with the problem's numbers filled in.

  1. Angle of list after loading a heavy lift off the centreline

    A general cargo ship displaces 12 500 t with KM 8.20 m, solid KG 7.30 m and free surface moments of 1250 t·m. She loads a 150 t heavy lift, which lands with its centre of gravity 11.0 m above the keel and 6.0 m to starboard of the centreline. Take KM as unchanged. What is the resulting angle of list?

    Show the answer and worked solution

    Answer: D, 5.37°

    1. New displacement: 12 500 + 150 = 12 650 t; new KG = (12 500 × 7.30 + 150 × 11.0) / 12 650 = 7.344 m.
    2. Free surface correction: 1250 / 12 650 = 0.099 m, so the fluid GM = 8.20 − 7.344 − 0.099 = 0.757 m.
    3. List: tan θ = w d / (Δ GM) = 150 × 6.0 / (12 650 × 0.757) = 0.0940, so θ = 5.37°.
    4. The traps: 4.75° ignores the free surface correction, 5.14° uses the fluid GM and displacement from before loading, and 4.57° uses the initial solid GM of 0.90 m and the old displacement.
  2. Change of forward draft after loading cargo forward

    A ship of 140 m LBP floats at drafts of 6.80 m forward and 7.40 m aft. TPC is 22 t/cm, MCTC is 160 t·m/cm and the LCF is 66 m forward of the aft perpendicular. She loads 250 t of cargo with its centre of gravity 110 m forward of the aft perpendicular. By how much does the forward draft change?

    Show the answer and worked solution

    Answer: B, 47.7 cm

    1. Bodily sinkage: w / TPC = 250 / 22 = 11.4 cm.
    2. Trimming moment about the LCF: 250 × (110 − 66) = 11 000 t·m by the head; change of trim = 11 000 / 160 = 68.8 cm.
    3. Share at the forward perpendicular: 68.8 × (140 − 66) / 140 = 36.3 cm.
    4. Forward draft change: 11.4 + 36.3 = 47.7 cm deeper.
    5. The traps: 45.7 cm splits the change of trim equally as if the LCF were amidships, 36.3 cm forgets the bodily sinkage, and 80.1 cm puts the whole change of trim at the bow.
  3. Sinkage of a box barge with a bilged midship compartment

    A box-shaped barge 60 m long, 12 m wide and 5.0 m deep floats on an even keel at a draft of 3.0 m. A midship compartment 12 m long, extending the full breadth, is bilged. The cargo in it gives a permeability of 0.85. What is the parallel sinkage of the barge?

    Show the answer and worked solution

    Answer: A, 0.614 m

    1. Lost buoyancy: v = μ l b d = 0.85 × 12 × 12 × 3.0 = 367.2 m³.
    2. Intact waterplane area: A = L B − μ l b = 720 − 0.85 × 144 = 597.6 m².
    3. Sinkage: v / A = 367.2 / 597.6 = 0.614 m.
    4. The traps: 0.510 m divides by the whole waterplane of 720 m², 0.750 m ignores the permeability, and 0.638 m applies the permeability to the lost volume but removes the whole 144 m² from the waterplane.
  4. GM at the critical instant of dry-docking

    A ship of 6000 t displacement enters a dry dock at drafts of 3.90 m forward and 5.00 m aft. MCTC is 95 t·m/cm and the LCF is 50 m forward of the aft perpendicular, where the keel first touches the blocks. KM is 7.00 m and KG is 6.20 m, with no slack tanks. Taking the loss of GM as P × KM / W, what is the GM at the critical instant?

    Show the answer and worked solution

    Answer: C, 0.556 m

    1. Trim by the stern: 5.00 − 3.90 = 1.10 m = 110 cm.
    2. Upthrust at the critical instant: P = MCTC × t / l = 95 × 110 / 50 = 209 t.
    3. Loss of GM: P × KM / W = 209 × 7.00 / 6000 = 0.244 m.
    4. GM = (7.00 − 6.20) − 0.244 = 0.556 m.
    5. The traps: 0.584 m uses P × KG / W, which mixes the two methods, 0.800 m ignores the upthrust altogether, and 0.772 m uses P × GM / W.
  5. Dock water allowance for a bulk carrier at a river berth

    A bulk carrier has LBP 180 m, breadth 30 m, summer draft 10.0 m, block coefficient 0.78 and waterplane coefficient 0.86 in sea water of 1.025 t/m³. She is loading at a river berth where the water density is 1.010 t/m³. What dock water allowance applies to her summer load line?

    Show the answer and worked solution

    Answer: B, 136 mm

    1. Displacement: Δ = L B T C_B ρ = 180 × 30 × 10.0 × 0.78 × 1.025 = 43 173 t.
    2. TPC = A_W ρ / 100 = 180 × 30 × 0.86 × 1.025 / 100 = 47.6 t/cm.
    3. FWA = Δ / (4 TPC) = 43 173 / (4 × 47.6) = 227 mm.
    4. DWA = FWA × (1025 − 1010) / 25 = 227 × 15 / 25 = 136 mm.
    5. The traps: 227 mm is the full fresh water allowance, 91 mm scales the FWA by (1010 − 1000) / 25, the distance from fresh water instead of from sea water, and 544 mm leaves the 4 out of the FWA formula.
  6. Power for a lower ballast speed by the Admiralty coefficient

    On sea trials a tanker loaded to 52 000 t displacement made 14.5 kn with 9800 kW of shaft power. In ballast she displaces 38 000 t and the owner wants 13.0 kn. Assuming the Admiralty coefficient stays constant, with power proportional to Δ^(2/3) V³, what shaft power is needed in ballast?

    Show the answer and worked solution

    Answer: D, 5730 kW

    1. Constant Admiralty coefficient: P2 = P1 × (Δ2 / Δ1)^(2/3) × (V2 / V1)³.
    2. Displacement factor: (38 000 / 52 000)^(2/3) = 0.811; speed factor: (13.0 / 14.5)³ = 0.721.
    3. P2 = 9800 × 0.811 × 0.721 = 5730 kW.
    4. The traps: 7060 kW scales the speed but ignores the lighter displacement, 5160 kW takes the power as proportional to Δ instead of Δ^(2/3), and 6390 kW scales with V² instead of V³.
  7. Real slip of a propeller with wake and current

    A ship's propeller has a pitch of 5.2 m and turns at 105 rpm. The GPS shows 15.2 kn over the ground, helped by a following current of 0.6 kn. The Taylor wake fraction is 0.25. What is the real slip of the propeller?

    Show the answer and worked solution

    Answer: A, 38.1 %

    1. Theoretical speed: V_t = P n = 5.2 × 105 × 60 / 1852 = 17.69 kn.
    2. Speed through the water: 15.2 − 0.6 = 14.6 kn; speed of advance: V_a = 14.6 × (1 − 0.25) = 10.95 kn.
    3. Real slip: (V_t − V_a) / V_t = (17.69 − 10.95) / 17.69 = 38.1 %.
    4. The traps: 14.1 % is the apparent slip against the speed over ground, 17.5 % is the slip against the speed through the water without the wake, and 35.6 % applies the wake but forgets to take off the following current.
  8. Metacentric height from an observed roll period

    The master of a bulk carrier times the natural roll in calm water at 16.0 s. The ship has a moulded breadth of 32.2 m, a mean draft of 12.0 m and a waterline length of 220 m. Using the IMO Intact Stability Code relation T = 2 C B / √GM, with C = 0.373 + 0.023 B/d − 0.043 L/100, what is the GM?

    Show the answer and worked solution

    Answer: C, 1.87 m

    1. Roll coefficient: C = 0.373 + 0.023 × 32.2 / 12.0 − 0.043 × 220 / 100 = 0.340.
    2. Rearranged: GM = (2 C B / T)² = (2 × 0.340 × 32.2 / 16.0)² = 1.369² = 1.87 m.
    3. The traps: 1.37 m forgets to square, 2.59 m uses the rule-of-thumb C = 0.40 instead of the IS Code formula, and 0.47 m drops the factor 2 and works out (C B / T)².
  9. Starting air receiver capacity for a reversible main engine

    A ship has one reversible two-stroke main engine. The engine maker states 2.5 m³ of free air (at atmospheric pressure) per start. The receivers are charged to 30 bar gauge and the engine starts reliably down to 9 bar gauge. Take atmospheric pressure as 1.013 bar and the expansion as isothermal. Under IACS UR M61, what total receiver volume is required?

    Show the answer and worked solution

    Answer: B, 1.45 m³

    1. UR M61 requires 12 consecutive starts, alternately ahead and astern, for a reversible engine: 12 × 2.5 = 30 m³ of free air.
    2. Isothermal: each m³ of receiver delivers (p1 − p2) / p_atm = (31.01 − 10.01) / 1.013 = 20.7 m³ of free air between 30 and 9 bar gauge.
    3. Receiver volume: V = 30 / 20.7 = 1.45 m³, normally split between two receivers.
    4. The traps: 1.01 m³ lets the air expand all the way to atmospheric pressure instead of stopping at 9 bar, 0.72 m³ allows only the 6 starts of a non-reversible engine, and 2.90 m³ counts 12 starts ahead plus 12 astern.
  10. Maximum squat of a tanker in a dredged channel

    A loaded tanker with block coefficient 0.82, breadth 40 m and draft 12.5 m transits a dredged channel 250 m wide at the bed with 14.5 m of water. She proceeds at 8.0 kn through the water. Using the Barrass formula squat = C_B S^0.81 V^2.08 / 20, with the blockage factor S = B T / (W h), what is the maximum squat?

    Show the answer and worked solution

    Answer: A, 0.623 m

    1. Blockage factor: S = B T / (W h) = 40 × 12.5 / (250 × 14.5) = 0.138.
    2. Squat = 0.82 × 0.138^0.81 × 8.0^2.08 / 20 = 0.82 × 0.201 × 75.6 / 20 = 0.623 m, at the bow because C_B is above 0.70.
    3. The traps: 0.525 m is the open-water rule of thumb C_B V² / 100, 1.050 m is the confined-channel rule of thumb 2 C_B V² / 100, and 0.156 m puts the speed into the formula in m/s instead of knots.

Results are estimates. They do not replace the governing code, class or flag requirements, or a check by a competent person.