Engineering reference tables
Tables engineers look up every day, generated from the same data and equations the calculators use, so a table and its calculator always agree. Each one names its standard or source.
Every table downloads as a CSV file and is free to reuse under CC BY 4.0, with a link to its page. Tables of regulatory figures, such as CII and FuelEU, show when they were last checked against the regulations.
- Reference tableSaturated steam table by temperatureSaturated water and steam properties from 0.01 to 350 °C: pressure, specific volume, enthalpy and entropy, computed with IAPWS-IF97.
- Reference tableSaturated steam table by pressureSaturated steam properties from 1 kPa to 16 MPa: boiling temperature, specific volume, enthalpy, latent heat and entropy, computed with IAPWS-IF97.
- Reference tableTap drill chart (metric, UNC and UNF)Tap drill sizes for metric coarse and fine threads M2 to M24 and UNC and UNF threads #4 to 1 in, with the thread percentage each drill gives.
- Reference tableDensity of common materialsDensity table of metals, timber, concrete, liquids and gases in kg/m³ and lb/ft³, with specific gravity and the standard behind each value.
- Reference tableInternational Standard Atmosphere tableISA standard atmosphere from sea level to 20 km and 50 000 ft: temperature, pressure, density, density ratio and speed of sound.
- Reference tableW beam sizes and properties (wide-flange)Dimensions and section properties of common AISC W-shapes from W6 to W24: weight, area, depth, flange, web, Ix, Sx and Zx.
- Reference tableIPE beam sizes and propertiesIPE 80 to IPE 600 dimensions and properties: mass, height, flange width, thicknesses, root radius, area, Iy, Wel, Wpl and shear area.
- Reference tableRebar size chart (US and metric)Rebar sizes, diameters, areas and weights: US bars #3 to #18 to ASTM A615 and metric bars 6 to 50 mm, in both unit systems.
- Reference tablePipe roughness table (absolute roughness)Absolute roughness of pipe materials in mm, inches and feet, for the Moody chart and the Colebrook and Swamee–Jain friction factors.
- Reference tableSurface roughness chart (Ra and N grades)Surface roughness grades N1 to N12 with Ra in micrometres and microinches, and approximate RMS and Rz values for each grade.
- Reference tableStandard resistor values (E12, E24, E96)Standard resistor and capacitor values of the IEC 60063 E6, E12, E24 and E96 series, one decade each, with their tolerances.
- Reference tableHardness conversion chart (HRC, HRB, HV, HB)Rockwell C and B to Vickers and Brinell for steel, with approximate tensile strength, from ASTM E140 and ISO 18265.
- Reference tableBolt torque chart (metric, VDI 2230)Tightening torque and preload for ISO metric bolts M4 to M36 in classes 8.8, 10.9 and 12.9, oiled and dry, to 90 % of yield by VDI 2230.
- Reference tableBend allowance chart for 90° sheet metal bendsBend allowance and bend deduction for 90° bends in sheet 0.5 to 10 mm thick, inside radius 0.5 to 10 mm, with the DIN 6935 K-factor.
- Reference tablePress brake tonnage chart (air bending)Press brake force for air bending mild steel by thickness and V-die opening, in kN per metre and US tons per foot, metric and inch sizes.
- Reference tableAWG wire size chart (AWG to mm²)American Wire Gauge 4/0 to 40: diameter in inches and mm, area in mm² and kcmil, copper resistance, and the next metric cable size.
- Reference tableTransformer full-load current chart (kVA to amps)Full-load current of standard transformer ratings, three-phase and single-phase, at common voltages from 120 V to 11 kV.
- Reference tableSteel plate weight chart (kg/m² and lb/ft²)Weight of steel, stainless steel and aluminium plate per square metre and per square foot, by metric thickness and by gauge and inch size.
- Reference tableDew point chart (temperature and relative humidity)Dew point for air temperatures from 0 to 40 °C and 40 to 100 °F at 10 to 100 % relative humidity, at sea-level pressure.
- Reference tableMoment of inertia formulas for common shapesArea, second moment of area, section modulus and radius of gyration formulas for rectangles, tubes, circles, triangles and I-sections.
- Reference tableSpecific heat of common materialsSpecific heat capacity of water, ice, air, oils, metals, concrete and glass in J/kg·K, kJ/kg·K and Btu/lb·°F, with the energy to warm 1 kg by 10 K.
- Reference tableCII reduction factors and required CII by yearIMO CII reduction factors 2023 to 2030, the required CII of typical ships for each year, and the A to E rating boundaries by ship type.
- Reference tableFuelEU Maritime GHG intensity limitsFuelEU Maritime well-to-wake GHG intensity limits from 2025 to 2050, and how far the default intensities of fossil fuels sit above them.
- Reference tableEU ETS for shipping: phase-in and allowances per tonne of fuelEU ETS maritime phase-in from 40 % in 2024 to 100 % from 2026, the gases covered, and the allowances due per tonne of each fuel.
- Reference tableMarine fuel emission factors (Cf, LCV, well-to-wake)IMO CO₂ conversion factors Cf and FuelEU default lower calorific values and emission factors for marine fuels, with well-to-wake intensity.