How the numbers are checked
Every calculator on this site must reproduce a set of known answers before a new version goes live. This page shows how that works, how many checks each field has, which standards the calculators follow, and every correction made since launch.
- 284calculators
- 2030recorded checks
- 900cited sources
- 226standards cited
Before every release
The site is published by an automatic pipeline. Each step below must pass, or nothing is published and the live site stays as it was.
- Reference checks. Every calculator runs its recorded cases, 2030 in all, and each result must match its expected value within the stated tolerance.
- Worked examples. The worked example printed in each article is calculated again, and the calculator must give the same numbers to the digits printed. An article cannot drift away from its calculator.
- Robustness. Every calculator is run with its defaults, every option, each input at its limits and beyond them, and 300 random sets of inputs. It must either give a result or reject the inputs with a plain message: no crash, and no “NaN” or “undefined” where a number should be.
- The site itself. The pages are built and checked: every link and file resolves, every calculator page prints its own checks and sources, and the security rules hold.
The same pipeline recomputes the answers of the 120 practice problems and the simulators’ physics models.
Three kinds of check
- 1484 value checks
- A case with a known answer. The answer comes from a standard, a textbook, a published table or a hand calculation shown in full. Each calculator page says which, under “What this calculator is checked against”, so you can tell a check against ISO 15016 from a check against arithmetic.
- 284 worked-example checks
- The example in the article, recomputed, as described above. One per calculator that has a worked example.
- 262 behaviour checks
- Inputs that must be rejected, and warnings that must appear: a negative length, a value outside a standard’s range, a combination that has no physical meaning.
A check proves that the calculator reproduces its cases. It does not prove that the method suits your problem. That is what the assumptions and limits on each page are for.
Run them yourself
On any calculator page, the button under its list of checks runs every case in your own browser and marks each one passed or failed. Nothing is sent anywhere.
The whole library is public at github.com/engineeringbible/calculators. With Node.js installed, node run-tests.js runs every check and node fuzz.js runs the robustness test, on your own machine.
Checks by field
Each calculator, the number of checks it must pass and the sources it cites. The name opens its list of checks.
Maritime75 calculators, 588 checks
Mechanical32 calculators, 240 checks
Electrical37 calculators, 254 checks
Energy and renewables11 calculators, 74 checks
| Calculator | Checks | Value | Example | Behaviour | Sources |
|---|---|---|---|---|---|
| Battery charge time | 6 | 4 | 1 | 1 | 2 |
| Electricity cost and energy use | 6 | 4 | 1 | 1 | 2 |
| EV charging time and cost calculator | 7 | 5 | 1 | 1 | 4 |
| Heat pump vs gas boiler running cost calculator | 7 | 5 | 1 | 1 | 3 |
| Inverter size calculator | 7 | 5 | 1 | 1 | 3 |
| mAh to Wh battery capacity | 6 | 4 | 1 | 1 | 3 |
| Micro-hydro power calculator | 7 | 5 | 1 | 1 | 3 |
| Solar battery bank calculator | 7 | 5 | 1 | 1 | 3 |
| Solar panel calculator: how many panels do I need? | 6 | 4 | 1 | 1 | 3 |
| Solar panel payback calculator | 7 | 5 | 1 | 1 | 3 |
| Wind turbine power calculator | 8 | 6 | 1 | 1 | 3 |
HVAC and building services8 calculators, 50 checks
| Calculator | Checks | Value | Example | Behaviour | Sources |
|---|---|---|---|---|---|
| Air changes per hour (ACH) and CFM calculator | 6 | 4 | 1 | 1 | 2 |
| Air density calculator | 6 | 4 | 1 | 1 | 2 |
| BTU calculator: AC size for a room | 6 | 4 | 1 | 1 | 2 |
| Building heat loss calculator (U-values) | 6 | 4 | 1 | 1 | 3 |
| Dew point calculator | 6 | 4 | 1 | 1 | 3 |
| Duct size calculator | 6 | 4 | 1 | 1 | 2 |
| Latent and sensible heat calculator (air and water) | 7 | 5 | 1 | 1 | 3 |
| Mixed air temperature calculator (outdoor and return air) | 7 | 5 | 1 | 1 | 2 |
Fluids and pumps19 calculators, 136 checks
Process and chemical12 calculators, 81 checks
Manufacturing and machining12 calculators, 73 checks
Automotive and aerospace14 calculators, 94 checks
| Calculator | Checks | Value | Example | Behaviour | Sources |
|---|---|---|---|---|---|
| Compression ratio calculator | 6 | 4 | 1 | 1 | 2 |
| Density altitude calculator | 7 | 5 | 1 | 1 | 3 |
| Drag and lift force calculator | 7 | 5 | 1 | 1 | 4 |
| Engine displacement calculator | 6 | 4 | 1 | 1 | 2 |
| Fuel injector size calculator | 7 | 5 | 1 | 1 | 3 |
| Gear ratio and vehicle speed calculator | 6 | 4 | 1 | 1 | 2 |
| Horsepower calculator | 7 | 5 | 1 | 1 | 3 |
| Quarter-mile ET and trap speed calculator | 7 | 5 | 1 | 1 | 2 |
| Rocket equation calculator (delta-v) | 7 | 5 | 1 | 1 | 2 |
| Speed of sound and Mach number calculator | 7 | 5 | 1 | 1 | 2 |
| Stopping distance calculator | 7 | 5 | 1 | 1 | 2 |
| Thrust-to-weight, wing loading and stall speed calculator | 7 | 5 | 1 | 1 | 3 |
| Tire size calculator and comparison | 6 | 4 | 1 | 1 | 2 |
| True airspeed calculator (TAS and Mach) | 7 | 5 | 1 | 1 | 3 |
Structural17 calculators, 122 checks
Civil30 calculators, 194 checks
Thermal13 calculators, 94 checks
General4 calculators, 30 checks
| Calculator | Checks | Value | Example | Behaviour | Sources |
|---|---|---|---|---|---|
| Engineering unit converter | 9 | 7 | 1 | 1 | 4 |
| Measurement uncertainty (GUM) | 7 | 5 | 1 | 1 | 4 |
| Quick statistics of a series | 7 | 6 | 1 | 0 | 4 |
| Reliability and redundancy | 7 | 6 | 1 | 0 | 3 |
Standards the calculators cite
226 standards, regulations and procedures are cited by 160 of the 284 calculators. The rest follow textbooks and handbooks, which their pages name. Each standard is listed once, without its edition: the calculator’s own page gives the edition and the clause it uses.
ISO (International Organization for Standardization)55
- ISO 68-1Bolt torque and preload
- ISO 76Rolling bearing L10 life (ISO 281)
- ISO 91Bunker quantity and density correction, Thermal expansion and restraint stress
- ISO 91-1Bunker quantity and density correction
- ISO 261Bolt torque and preload, Tap drill size calculator (metric and UNC/UNF)
- ISO 262Tap drill size calculator (metric and UNC/UNF)
- ISO 273Bolt torque and preload
- ISO 281Rolling bearing L10 life (ISO 281)
- ISO 724Bolt torque and preload, Tap drill size calculator (metric and UNC/UNF)
- ISO 898-1Bolt torque and preload
- ISO 1302Surface finish converter (Ra, RMS, Rz, N grades)
- ISO 1704Anchor cable catenary and scope
- ISO 2533Air density calculator, Hydrostatic pressure at depth, Ideal gas law (PV = nRT), Wind turbine power calculator
- ISO 3046Engine power and SFOC to ISO 3046 conditions
- ISO 3046-1Bunker quantity and density correction, Engine BMEP, torque and power, Engine power and SFOC to ISO 3046 conditions, Fuel consumption and voyage cost, Fuel net specific energy and CO₂ factor
- ISO 3320Hydraulic cylinder force and speed
- ISO 3448Blending ratio calculator (two liquids to a target property)
- ISO 3506-1Bolt torque and preload
- ISO 4000-1Tire size calculator and comparison
- ISO 4014Bolt torque and preload
- ISO 4017Bolt torque and preload
- ISO 4184V-belt length and centre distance calculator
- ISO 4287Surface finish converter (Ra, RMS, Rz, N grades)
- ISO 4393Hydraulic cylinder force and speed
- ISO 4677-1Cargo ventilation and dew point
- ISO 5167-1Orifice and venturi flow (ISO 5167)
- ISO 5167-2Orifice and venturi flow (ISO 5167)
- ISO 5167-4Orifice and venturi flow (ISO 5167)
- ISO 5725-2Quick statistics of a series
- ISO 7507-1Tank sounding trim and heel correction
- ISO 8217Alternative fuel tank volume, Bunker quantity and density correction, Fuel blending and heating viscosity, Fuel net specific energy and CO₂ factor
- ISO 8503Paint coverage and quantity
- ISO 8528-1Generator load, kVA and fuel, Generator size calculator, kVA to kW, kW to kVA
- ISO 8528-5Motor starting current and voltage dip
- ISO 8778Mass flow rate calculator (kg/h, m³/h, velocity, Nm³/h, SCFM)
- ISO 8861Engine-room ventilation (ISO 8861)
- ISO 8995-1Lighting design (lumen method)
- ISO 9906Pump NPSH and suction lift
- ISO 10816-3Vibration isolation and severity
- ISO 12241Pipe and tank insulation heat loss
- ISO 12473Cathodic protection anodes
- ISO 13443Mass flow rate calculator (kg/h, m³/h, velocity, Nm³/h, SCFM)
- ISO 14179-1Gear ratio, rpm and torque
- ISO 15016Added resistance in waves (STAwave-1), Hull roughness and fouling penalty, Rotor sail (Flettner rotor) thrust and saving, Shallow water correction (Raven / Lackenby), Speed–power curve fit, True wind from apparent wind, Water temperature and density correction, Wind resistance (ISO 15016)
- ISO 15550Bunker quantity and density correction, Engine power and SFOC to ISO 3046 conditions
- ISO 15589-2Cathodic protection anodes
- ISO 18265Hardness conversion calculator (HRC, HRB, HV, HB)
- ISO 19030-1Energy-saving device payback
- ISO 19030-2Speed–power curve fit, Wind resistance (ISO 15016)
- ISO 19030-3Fuel net specific energy and CO₂ factor
- ISO 19840Paint coverage and quantity
- ISO 20816-3Vibration isolation and severity
- ISO 22400-2OEE and takt time calculator
- ISO 80000-3Hydrostatic pressure at depth
- ISO 80000-6Electricity cost and energy use
IEC (International Electrotechnical Commission)41
- IEC 60027-3Decibel calculator (dB, dBm, dBV, dBu)
- IEC 60028AWG wire gauge chart and converter, Cable sizing and voltage drop, PCB trace width calculator (IPC-2221)
- IEC 60034-1kW to amps, Three-phase power and motor current
- IEC 60034-12Motor starting current and voltage dip, Three-phase power and motor current
- IEC 60034-30-1kW to amps, Pump power calculator, Three-phase power and motor current
- IEC 60038Amps to watts, Watts to amps
- IEC 60050-131Electricity cost and energy use, Ohm's law and electrical power
- IEC 60059Breaker size calculator
- IEC 60062Resistor colour code, Series and parallel capacitors, Series and parallel resistors
- IEC 60063555 timer calculator, LED series resistor, Resistor colour code, Voltage divider
- IEC 60072-1Pump power calculator
- IEC 60076-1kVA to amps, Transformer size calculator (kVA)
- IEC 60076-7Transformer size calculator (kVA)
- IEC 60076-8Transformer size calculator (kVA)
- IEC 60092-201Cable sizing and voltage drop
- IEC 60092-301Generator load sharing with droop, Generator load, kVA and fuel
- IEC 60092-352Cable sizing and voltage drop
- IEC 60228AWG wire gauge chart and converter, Cable sizing and voltage drop, Wire size calculator (AWG and mm²)
- IEC 60287-1-1Cable sizing and voltage drop
- IEC 60364-4-41Cable short-circuit withstand
- IEC 60364-4-43Breaker size calculator, Cable short-circuit withstand, Short-circuit current (IEC 60909)
- IEC 60364-5-52Cable sizing and voltage drop, Wire size calculator (AWG and mm²)
- IEC 60364-5-54Cable short-circuit withstand
- IEC 60534-2-1Control valve Cv / Kv sizing
- IEC 60534-8-4Control valve Cv / Kv sizing
- IEC 60831-1Power factor correction
- IEC 60896-11Battery capacity and runtime
- IEC 60896-21Battery capacity and runtime
- IEC 60898-1Breaker size calculator
- IEC 60909-0Cable short-circuit withstand, Short-circuit current (IEC 60909)
- IEC 60947-2Short-circuit current (IEC 60909)
- IEC 60949Cable short-circuit withstand
- IEC 61078Reliability and redundancy
- IEC 61174Passage plan from waypoints
- IEC 61215-1Solar panel calculator: how many panels do I need?
- IEC 61400-12-1Wind turbine power calculator
- IEC 61427-1Battery charge time
- IEC 61642Power factor correction
- IEC 61649Reliability and redundancy
- IEC 61960-3mAh to Wh battery capacity
- IEC 62301Electricity cost and energy use
EN (European standards, including the Eurocodes)33
- EN 206Concrete volume and rebar weight
- EN 228Boat fuel consumption calculator, Density calculator (mass, volume and density), Fuel injector size calculator
- EN 338Beam deflection and bending stress, Column buckling (Euler and Johnson), Density calculator (mass, volume and density), Material properties table (steel, aluminium, plastics)
- EN 572-1Density calculator (mass, volume and density), Material properties table (steel, aluminium, plastics)
- EN 590Boat fuel consumption calculator, Density calculator (mass, volume and density)
- EN 818-4Lifting sling and wire rope load, Wire rope and chain safe working load calculator
- EN 1011-2Carbon equivalent calculator (CE, Pcm, CET) and preheat
- EN 1506Duct size calculator
- EN 1991-1-1Concrete volume and rebar weight, Material properties table (steel, aluminium, plastics)
- EN 1991-1-3Snow load calculator (Eurocode and ASCE 7)
- EN 1991-1-4Wind load calculator (Eurocode and ASCE 7)
- EN 1992-1-1Concrete volume and rebar weight, Deflection limits calculator (L/360, L/240), Material properties table (steel, aluminium, plastics), Rebar weight and quantity calculator
- EN 1992-1-2Material properties table (steel, aluminium, plastics)
- EN 1993-1-1Beam deflection and bending stress, Column buckling (Euler and Johnson), Deflection limits calculator (L/360, L/240), Density calculator (mass, volume and density), Elastic constants calculator (E, G, K, Poisson's ratio), Fillet weld strength, Material properties table (steel, aluminium, plastics), Moment of inertia calculator (section properties), Padeye design check, Shaft torsion calculator (shear stress, twist, diameter), Steel and metal weight calculator, Steel beam size calculator, Stress and strain calculator (Young's modulus)
- EN 1993-1-2Material properties table (steel, aluminium, plastics)
- EN 1993-1-8Fillet weld strength, Padeye design check
- EN 1995-1-1Deflection limits calculator (L/360, L/240)
- EN 1997-1Footing size calculator, Retaining wall earth pressure calculator (Rankine), Soil bearing capacity calculator (Terzaghi and Eurocode 7)
- EN 1999-1-1Elastic constants calculator (E, G, K, Poisson's ratio), Material properties table (steel, aluminium, plastics), Shaft torsion calculator (shear stress, twist, diameter), Stress and strain calculator (Young's modulus)
- EN 10025-2Fillet weld strength
- EN 10080Rebar weight and quantity calculator
- EN 10088-1Density calculator (mass, volume and density), Steel and metal weight calculator
- EN 10219-2Steel and metal weight calculator
- EN 10365Beam deflection and bending stress, Steel beam size calculator
- EN 12385-4Lifting sling and wire rope load, Wire rope and chain safe working load calculator, Wire rope weight calculator
- EN 12464-1Lighting design (lumen method)
- EN 12831-1Building heat loss calculator (U-values)
- EN 13414-1Lifting sling and wire rope load, Wire rope and chain safe working load calculator
- EN 13906-1Spring rate calculator (helical compression spring)
- EN 14214Alternative fuel tank volume
- EN 14511-2Carnot efficiency and COP calculator
- EN 14825Heat pump vs gas boiler running cost calculator
- EN 15940Alternative fuel tank volume
IMO (International Maritime Organization) resolutions and circulars28
- MEPC.1/Circ.875Bunker quantity and density correction
- MEPC.1/Circ.896Energy-saving device payback
- MEPC.124Ballast water exchange time
- MEPC.176NOx tier limit by engine speed
- MEPC.177NOx tier limit by engine speed
- MEPC.251NOx tier limit by engine speed
- MEPC.286NOx tier limit by engine speed
- MEPC.297Ballast water exchange time
- MEPC.338CII rating estimator
- MEPC.352CII rating estimator
- MEPC.353CII rating estimator
- MEPC.354CII rating estimator
- MEPC.364CII rating estimator, Energy-saving device payback, Fuel consumption and voyage cost, Fuel net specific energy and CO₂ factor, Generator load, kVA and fuel, Optimal speed under charter
- MEPC.378Optimal hull cleaning interval
- MEPC.400CII rating estimator
- MSC.1/Circ.1175Mooring line and winch brake (MEG4)
- MSC.1/Circ.1200Roll period and synchronous rolling
- MSC.1/Circ.1228Roll period and synchronous rolling, Wave properties and encounter period
- MSC.1/Circ.1281GZ curve and intact stability criteria
- MSC.1/Circ.1353/Rev.2Cargo securing (CSS Code Annex 13)
- MSC.1/Circ.1537GZ curve and intact stability criteria
- MSC.23GZ curve and intact stability criteria
- MSC.192CPA and TCPA from radar plots
- MSC.206Fixed CO₂ fire-extinguishing system
- MSC.267GZ curve and intact stability criteria, Inclining experiment, Initial stability GM and list, Loading condition from an item list, Roll period and synchronous rolling
- MSC.339Fixed CO₂ fire-extinguishing system
- MSC.391Alternative fuel tank volume
- MSC.581Enclosed space purge time
European Union regulations2
- Regulation (EU) 2023/957Energy-saving device payback, EU ETS and FuelEU Maritime
- Regulation (EU) 2023/1805Alternative fuel tank volume, EU ETS and FuelEU Maritime, Fuel net specific energy and CO₂ factor
ASTM International25
- ASTM A36Material properties table (steel, aluminium, plastics)
- ASTM A106Pipe wall thickness (ASME B31.3)
- ASTM A228Spring rate calculator (helical compression spring)
- ASTM A370Hardness conversion calculator (HRC, HRB, HV, HB)
- ASTM A530/A530MPipe wall thickness (ASME B31.3)
- ASTM A615/A615MRebar weight and quantity calculator
- ASTM A973Wire rope and chain safe working load calculator
- ASTM A1023/A1023MWire rope weight calculator
- ASTM B8AWG wire gauge chart and converter, Wire size calculator (AWG and mm²)
- ASTM B258AWG wire gauge chart and converter, Wire size calculator (AWG and mm²)
- ASTM C1055Pipe and tank insulation heat loss
- ASTM D287Specific gravity calculator (SG, API gravity, Baumé)
- ASTM D341Fuel blending and heating viscosity
- ASTM D445cSt to SSU viscosity converter (Saybolt seconds)
- ASTM D698Soil compaction calculator (Proctor relative compaction)
- ASTM D1250Bunker quantity and density correction, Specific gravity calculator (SG, API gravity, Baumé), Thermal expansion and restraint stress
- ASTM D1556Soil compaction calculator (Proctor relative compaction)
- ASTM D1557Soil compaction calculator (Proctor relative compaction)
- ASTM D2161cSt to SSU viscosity converter (Saybolt seconds)
- ASTM D2435Consolidation settlement calculator (clay layer)
- ASTM D6938Soil compaction calculator (Proctor relative compaction)
- ASTM D7152Blending ratio calculator (two liquids to a target property), Fuel blending and heating viscosity
- ASTM E100Specific gravity calculator (SG, API gravity, Baumé)
- ASTM E140Hardness conversion calculator (HRC, HRB, HV, HB)
- ASTM F1321Inclining experiment
ASME (American Society of Mechanical Engineers)6
- ASME B1.1Tap drill size calculator (metric and UNC/UNF)
- ASME B29.100Chain and sprocket calculator (roller chain length)
- ASME B30.9Lifting sling and wire rope load
- ASME B31.3Pipe wall thickness (ASME B31.3), Thermal expansion and restraint stress
- ASME B36.10MPipe volume and mass of contents, Pipe wall thickness (ASME B31.3)
- ASME B94.11MTap drill size calculator (metric and UNC/UNF)
API (American Petroleum Institute)3
ASHRAE1
IEEE7
- IEEE 141Three-phase power and motor current
- IEEE 485Battery capacity and runtime, Solar battery bank calculator
- IEEE 1013Solar battery bank calculator, Solar PV array and storage sizing
- IEEE 1036Power factor correction
- IEEE 1459Amps to kW
- IEEE 1562Inverter size calculator, Solar PV array and storage sizing
- IEEE C57.12.00Transformer size calculator (kVA)
NFPA (National Fire Protection Association)4
- NFPA 12Fixed CO₂ fire-extinguishing system
- NFPA 13Hazen–Williams head loss calculator, Nozzle flow calculator (orifice, fire nozzle and K-factor)
- NFPA 70Breaker size calculator, Conduit fill calculator (NEC), Generator size calculator, Wire size calculator (AWG and mm²)
- NFPA 291Nozzle flow calculator (orifice, fire nozzle and K-factor)
ACI (American Concrete Institute)2
AISC (American Institute of Steel Construction)1
ASCE (American Society of Civil Engineers)1
AWS (American Welding Society)1
BS (British Standards)6
- BS 1363Amps to watts
- BS 6031Earthwork cut and fill volumes
- BS 6349-4Berthing energy and fender selection
- BS 7121-3Crane outrigger pad bearing pressure
- BS 8004Crane outrigger pad bearing pressure
- BS 8500Concrete volume and rebar weight
DIN (German standards)3
ITTC (International Towing Tank Conference) procedures2
- ITTC 7.5-02-01-03Added resistance in waves (STAwave-1), Hull roughness and fouling penalty, Hydrostatic pressure at depth, Pipe volume and mass of contents
- ITTC 7.5-04-01-01.1Water temperature and density correction
IAPWS (International Association for the Properties of Water and Steam)1
Other standards bodies4
- JCGM 100Measurement uncertainty (GUM)
- JCGM 101Measurement uncertainty (GUM)
- NIST SP 811Asphalt calculator: tons of hot mix, Gravel calculator: cubic yards and tons
- PIANC WG211Berthing energy and fender selection
Corrections
No published result has needed a correction since the site went live on 2 November 2026. When one does, it is listed here: the date, the pages and results affected, what was wrong and since when, and what changed. The fixed calculator also gains a check for that case, so the error cannot return.
Other changes, including fixes that did not affect a result, are on What’s new.
Found an error?
Write to contact@engineeringbible.com with the page and the inputs you used. The share link under each calculator records the inputs, so pasting it into the message is the quickest way. Say what you expected and where it comes from: a standard, a textbook or your own calculation. Corrections come before any other work. More on the contact page.