Skip to content
Engineering Bible

Results appear as you type. Use the arrow keys to move through them and Enter to open one.

Popular

↑ ↓ moveEnter openEsc close

Bend allowance chart for 90° sheet metal bends

Bend allowance is the length of the neutral axis through a bend: add it to the flat lengths of the legs to get the blank. Bend deduction is the amount to take off the sum of the outside flange dimensions instead. Both depend on the thickness t, the inside radius R and the K-factor, the position of the neutral axis. A 2 mm sheet bent to a 2 mm inside radius needs a bend allowance of 4.16 mm and a bend deduction of 3.84 mm.

Free to reuse under CC BY 4.0 with a link to this page. Each table downloads as a CSV file.

To compute any value directly: Bend allowance calculator (sheet metal flat length)

Bend allowance BA (mm) at 90°, rows thickness t (mm), columns inside radius R (mm)

t \ RR 0.5R 1R 1.5R 2R 3R 4R 5R 6R 8R 10
0.51.041.892.713.525.116.688.259.8212.9616.10
0.81.132.012.853.685.306.918.4810.0513.1916.34
11.182.082.943.775.417.038.6410.2113.3516.49
1.51.272.233.123.985.667.308.9310.5513.7416.89
21.332.363.284.165.877.549.1910.8214.0617.28
2.51.382.463.414.326.077.769.4311.0714.3417.58
31.402.543.534.476.247.969.6511.3114.6017.86
41.412.673.734.716.568.3310.0511.7415.0818.38
51.372.753.884.916.838.6510.4112.1315.5218.85
61.312.804.005.087.078.9310.7312.4915.9219.29
81.092.824.165.337.469.4211.3013.1216.6520.10
100.782.754.235.507.769.8311.7813.6617.2920.81

Download this table as CSV

Bend deduction BD (mm) at 90°, rows thickness t (mm), columns inside radius R (mm)

t \ RR 0.5R 1R 1.5R 2R 3R 4R 5R 6R 8R 10
0.50.961.111.291.481.892.322.753.184.044.90
0.81.471.591.751.922.302.693.123.554.415.26
11.821.922.062.232.592.973.363.794.655.51
1.52.732.772.883.023.343.704.074.455.266.11
23.673.643.723.844.134.464.815.185.946.72
2.54.624.544.594.684.935.245.575.936.667.42
35.605.465.475.535.766.046.356.697.408.14
47.597.337.277.297.447.677.958.268.929.62
59.639.259.129.099.179.359.599.8710.4811.15
611.6911.2011.0010.9210.9311.0711.2711.5112.0812.71
815.9115.1814.8414.6714.5414.5814.7014.8815.3515.90
1020.2219.2518.7718.5018.2418.1718.2218.3418.7119.19

Download this table as CSV

How the table was made

Computed with the bend allowance calculator’s functions: BA = θ (R + K t) and BD = 2 (R + t) tan(θ/2) − BA, with θ = π/2 and K from DIN 6935, K = (0.65 + 0.5 log₁₀(R/t)) / 2, reaching 0.5 at R/t ≥ 5.

The K-factor depends on the material, the tooling and air bending versus bottoming. For production work, bend a test piece and adjust K; a chart from the press brake maker for your tooling is better still.

FAQ

What is the difference between bend allowance and bend deduction?
Bend allowance is added to the inside flat lengths; bend deduction is taken off the sum of the outside dimensions. Both give the same blank length.

What K-factor should I use?
DIN 6935 gives K = 0.33 when the inside radius equals the thickness, less for tighter bends, rising to 0.5 once the radius is five times the thickness. A test bend gives the real value for your material and tools.

Sources

  • DIN 6935:2011, Cold bending of flat rolled steel products (correction factor and neutral fibre).
  • Benson, S. D., Press Brake Technology (SME, 1997): bend allowance, outside setback and bend deduction.

Results are estimates. They do not replace the governing code, class or flag requirements, or a check by a competent person. Report a problem