Skip to content
Engineering Bible

Results appear as you type. Use the arrow keys to move through them and Enter to open one.

Popular

↑ ↓ moveEnter openEsc close

Bolt torque chart (metric, VDI 2230)

A bolt torque chart gives the tightening torque M_A that produces a target preload F_M in the bolt. These charts use the VDI 2230 method, tightening to 90 % of the yield strength under the combined tension and thread torsion, for ISO coarse threads with standard hex heads. Friction matters more than anything else: the same M12 class 8.8 bolt needs 93 N·m dry and zinc-plated but about 84 N·m lightly oiled, for nearly the same preload.

Free to reuse under CC BY 4.0 with a link to this page. Each table downloads as a CSV file.

To compute any value directly: Bolt torque and preload

Lightly oiled or zinc-flake coated, μ = 0.12 (friction class B)

Size8.8: FM (kN)8.8: MA (N·m)10.9: FM (kN)10.9: MA (N·m)12.9: FM (kN)12.9: MA (N·m)
M44.42.966.54.357.65.09
M57.25.8410.68.5812.410.0
M610.210.115.014.917.517.4
M818.624.627.436.132.042.2
M1029.648.543.571.250.983.3
M1243.183.663.312374.1144
M1459.113486.9196101.7230
M1681.0206118.9302139.2354
M20130.5416185.8592217.5693
M24187.9715267.61 018313.21 191
M30300.01 429427.22 035499.92 381
M36438.12 483624.03 537730.24 139

Download this table as CSV

Dry, zinc-plated or phosphated, μ = 0.14 (friction class C)

Size8.8: FM (kN)8.8: MA (N·m)10.9: FM (kN)10.9: MA (N·m)12.9: FM (kN)12.9: MA (N·m)
M44.33.286.34.827.45.64
M57.06.4810.39.5212.011.1
M69.911.314.616.517.019.3
M818.127.326.640.131.246.9
M1028.853.942.379.249.592.6
M1242.093.161.713772.2160
M1457.614984.621899.0256
M1678.9230115.9338135.7395
M20127.2464181.1661212.0773
M24183.1798260.81 136305.21 330
M30292.51 598416.62 276487.52 663
M36427.32 780608.63 959712.24 633

Download this table as CSV

How the table was made

Each row is the bolt torque calculator’s result: VDI 2230 Part 1 (2015) torque relation M_A = F_M (0.16 P + 0.58 d₂ μ_G + D_Km μ_K / 2) with equal thread and head friction, and the preload that brings the reduced stress to 90 % of the ISO 898-1 minimum yield strength. D_Km is the mean of the hex head bearing face and a medium clearance hole.

F_M is the assembly preload. Torque tightening scatters, so the joint has to work with the minimum preload, F_M divided by the tightening factor (about 1.6 to 2 for a torque wrench). Washers, flange heads, socket heads and other coatings change the friction and the torque.

FAQ

What torque for an M10 class 8.8 bolt?
About 54 N·m dry and zinc-plated (μ 0.14) for a preload of 28.8 kN, or 48.5 N·m lightly oiled (μ 0.12) for 29.6 kN.

Why does a greased bolt need less torque?
Most of the torque goes into friction under the head and in the thread. Lower friction leaves more of it to stretch the bolt, so the same preload takes less torque, and the dry torque would overload a greased bolt.

  • Bolt torque and preload: Preload and tightening torque for ISO metric bolts by the VDI 2230 method, with property class, friction, proof load and preload scatter.
  • Tap drill size calculator (metric and UNC/UNF): Tap drill for metric coarse and fine and UNC/UNF threads at any percentage of thread, with the nearest standard drill and the basic pitch and minor diameters.

Sources

  • VDI 2230 Part 1:2015, Systematic calculation of highly stressed bolted joints.
  • ISO 898-1:2013, Mechanical properties of fasteners: bolts, screws and studs.
  • ISO 261 and ISO 724, ISO general purpose metric screw threads.

Results are estimates. They do not replace the governing code, class or flag requirements, or a check by a competent person. Report a problem