Mild steel (414 MPa tensile), kN per metre of bend length
| t (mm) | V = 6 t | V = 8 t | V = 10 t | V = 12 t |
|---|---|---|---|---|
| 0.8 | 88 | 66 | 53 | 44 |
| 1 | 110 | 83 | 66 | 55 |
| 1.5 | 165 | 124 | 99 | 83 |
| 2 | 220 | 165 | 132 | 110 |
| 2.5 | 276 | 207 | 165 | 138 |
| 3 | 331 | 248 | 198 | 165 |
| 4 | 441 | 331 | 265 | 220 |
| 5 | 551 | 413 | 331 | 276 |
| 6 | 661 | 496 | 397 | 331 |
| 8 | 882 | 661 | 529 | 441 |
| 10 | 1 102 | 827 | 661 | 551 |
| 12 | 1 323 | 992 | 794 | 661 |
| 15 | 1 653 | 1 240 | 992 | 827 |
| 20 | 2 204 | 1 653 | 1 323 | 1 102 |
Mild steel (60 ksi tensile), US tons per foot, V = 8 t
| Thickness | V (in) | tons/ft |
|---|---|---|
| 16 ga (0.0598 in) | 0.478 | 4.3 |
| 14 ga (0.0747 in) | 0.598 | 5.4 |
| 12 ga (0.1046 in) | 0.837 | 7.5 |
| 10 ga (0.1345 in) | 1.076 | 9.7 |
| 3/16 in | 1.500 | 13.5 |
| 1/4 in | 2.000 | 18.0 |
| 5/16 in | 2.500 | 22.5 |
| 3/8 in | 3.000 | 27.0 |
| 1/2 in | 4.000 | 36.0 |
| 5/8 in | 5.000 | 45.0 |
| 3/4 in | 6.000 | 53.9 |
How the table was made
Each value is the press tonnage calculator’s air-bending force for mild steel with a tensile strength of 414 MPa (60 ksi): the press brake makers’ formula 575 t² / V US tons per foot, with t and V in inches, for 60 ksi steel. In SI that is F ≈ 1.6 × Rm × t² × L / V. For another material multiply by its tensile strength divided by 414 MPa: about 1.3 to 1.5 for austenitic stainless steel and 0.5 to 0.6 for 5052 aluminium.
Bottoming and coining need three to five times the air-bending force or more. Keep a margin below the press rating, and check the die and punch ratings too.
FAQ
What V-die opening should I use?
About eight times the thickness for mild steel. A narrower die needs more force and leaves a smaller radius; a wider one needs less force and gives a larger radius.
How much tonnage to bend 1/4 in plate?
About 18 US tons per foot over a 2 in die in mild steel.
Calculators that use this table
- Press tonnage calculator (punching and press brake): Punching and blanking force from perimeter, thickness and shear strength, with stripping force and press margin, and press brake air-bending tonnage.
- Bend allowance calculator (sheet metal flat length): Sheet metal bend allowance, bend deduction, outside setback and flat length for one or many bends, from thickness, radius, angle and K-factor.
- Steel and metal weight calculator: Weight of steel, stainless, aluminium, copper and brass plate, bar, tube, pipe, angle, beam and channel, per metre or foot, per piece and in total.
Sources
- Bystronic, How to calculate press brake tonnage: 575 × t² / V per foot for 60 000 psi steel, scaled by tensile strength.