Drawn for the default inputs. It redraws as you change them.
Results are estimates. They do not replace the governing code, class or flag requirements, or a check by a competent person. Report a problem
Introduction
How many bricks do you need? Divide the wall area by the face of one brick plus one mortar joint. A modular brick, 7⅝ × 2¼ in, laid with ⅜ in joints takes up 8 × 2⅝ in, so a square foot of wall holds 6.86 bricks. A wall of 148 ft² after deducting a window needs 1 015 bricks, or 1 066 with 5 % for cutting and breakage.
This calculator counts the bricks for a wall of any common US brick, the UK metric brick or a size you enter. It handles one or two wythes, deducts doors and windows and adds waste. It also gives the mortar volume in the joints and the bags of mortar mix. It is for masons, builders and homeowners pricing a wall, a veneer or a garden project.
Formulas
Bricks:
bricks per area = 1 / ((L + j) × (H + j))
bricks = A_net × bricks per area × wythes × (1 + waste)
Mortar, the method of BIA Technical Note 10:
mortar per brick = ((L + j) × (H + j) − L × H) × W
collar joint = A_net × j (double wythe only)
L, H, W — specified length, height and width of the brick
j — mortar joint thickness, ⅜ in in the US and 10 mm in metric brickwork
A_net — wall area less doors and windows
wythes — one or two thicknesses of brick
Brick
Size, in
Bricks per ft² with ⅜ in joints
Modular
7⅝ × 2¼ × 3⅝
6.86
Standard
8 × 2¼ × 3⅝
6.55
Queen
7⅝ × 2¾ × 2¾
5.76
Norman
11⅝ × 2¼ × 3⅝
4.57
Utility
11⅝ × 3⅝ × 3⅝
3.00
Assumptions and limitations
The wall is laid in running or stack bond with even joints. Bonds with header courses use more bricks; BIA TN 10 gives the correction factors.
BIA TN 10 lists 675 modular bricks per 100 ft² because three modular courses fill exactly 8 in. With joints of exactly ⅜ in the count is 686.
The mortar volume is the theoretical volume of full joints, with no waste. It reproduces the BIA figure of 8.1 ft³ per 1 000 modular bricks.
Bags use the QUIKRETE rate of 37 standard bricks per 80 lb bag of mortar mix, scaled to the chosen brick. That rate includes normal droppings and waste.
Load-bearing or tall brick walls need a design by an engineer.
Worked example
A wall is 20 ft long and 8 ft high with a window of 12 ft². It is built of modular brick with ⅜ in joints, one wythe thick. How many bricks and how much mortar are needed with 5 % waste?
Bricks: 148 × 6.857 = 1 014.9, so 1 015 bricks without waste.
With 5 % waste: 1 015 × 1.05 = 1 066 bricks.
Mortar per brick: (8 × 2.625 − 7.625 × 2.25) × 3.625 = 13.93 in³, or 8.06 ft³ per 1 000 bricks.
Mortar for the wall: 1 014.9 × 13.93 in³ = 8.18 ft³.
Bags: at 37 standard bricks per bag, 27 bags of 80 lb mortar mix.
The theoretical mortar is close to the 8.1 ft³ per 1 000 bricks in BIA TN 10 Table 4.
The worked example, drawn by the same code as the live drawing above.
FAQ
How many bricks are in a square foot?
6.86 modular bricks with ⅜ in joints, or 6.75 by the BIA modular coursing. Standard bricks give 6.55 per square foot.
How many bricks are in a square metre?
59.3 UK bricks of 215 × 65 mm with 10 mm joints, usually rounded to 60.
How many bricks for a double wythe wall?
Twice the single-wythe count. The mortared collar joint between the wythes adds 3.13 ft³ of mortar per 100 ft² at ⅜ in thick.
How much mortar do 1 000 bricks need?
About 8.1 ft³ of joint mortar for modular brick with ⅜ in joints, and 10.3 ft³ with ½ in joints. Real use is higher because of droppings.
How many bricks does a bag of mortar lay?
QUIKRETE gives up to 37 standard bricks per 80 lb bag of Mortar Mix. Masons often reckon eight bags of masonry cement, mixed with sand, per 1 000 bricks.
How much waste should I allow for bricks?
About 5 % on plain walls. Allow more for many openings, corners and cut bricks.
Before every release the calculator must reproduce each case below. The note under each case says where the expected answer comes from: a standard, a textbook, a published table, or a hand calculation shown in full.
BIA TN 10 Table 4, modular brick: mortar 8.1 ft³ per 1 000 bricks with ⅜ in joints and 10.3 with ½ in jointsBrick Industry Association TN 10 (2009), Table 4: modular 4 × 2⅔ × 8 nominal, ⅜ in 8.1 and ½ in 10.3 ft³ per 1 000 brick
BIA TN 10 Table 4 counts: standard brick 655 per 100 ft² and king 455 per 100 ft² with ⅜ in jointsBrick Industry Association TN 10, Table 4 (non-modular sizes); 144 / (8⅜ × 2⅝) = 6.55 per ft²
20 × 8 ft wall less a 12 ft² window, modular, ⅜ in joints: 1 015 bricks, 1 066 with 5 % waste, 8.18 ft³ of mortar, 27 bagsHand calculation: 148 ft² × 144 / (8 × 2.625) = 1 014.9; mortar (21 − 7.625 × 2.25) × 3.625 = 13.93 in³ per brick
Double wythe adds the collar joint of BIA TN 10 Table 5: 3.13 ft³ per 100 ft² for a ⅜ in jointBrick Industry Association TN 10, Table 5 (mortar in collar joints): ⅜ in, 3.13 ft³ per 100 ft²
UK bricks 215 × 65 mm with 10 mm joints: 59.3 per m²; zero joint warns; openings larger than the wall are rejectedBehaviour check: warnings and rejected inputs
Worked example of the article: the calculator reproduces 6.857, 1 015, 1 066, 8.18 ft³, 8.06 ft³, 27 to the digits printedThe worked example on this page, to the digits printed
Assumptions and sources
Assumptions and limits
Running or stack bond with every joint the same thickness. Each brick takes up its face plus one bed joint and one head joint; patterns with header courses use more bricks, by BIA TN 10 Table 6.
Mortar is the theoretical volume of full bed and head joints through the brick width, the method behind BIA TN 10 Table 4, with no waste; a double wythe adds a solid collar joint of the same thickness.
Mortar bags use the QUIKRETE Mortar Mix rate of 37 standard bricks per 80 lb bag, scaled by the joint mortar of the chosen brick; this rate includes the droppings and waste of normal laying.
The waste allowance on bricks covers cutting and breakage; 5 % is common for plain walls, more with many openings and corners.
Sources
Brick Industry Association, Technical Note 10, Dimensioning and Estimating Brick Masonry (2009), Table 4 (bricks and mortar per 100 ft²) and Table 5 (collar joints)
Brick Development Association, The BDA Guide to Successful Brickwork, 3rd ed. (2005): UK brick format 215 × 102.5 × 65 mm laid with 10 mm joints
QUIKRETE Mortar Mix No. 1102 data sheet (an 80 lb bag lays up to 37 standard bricks)
Cite this calculator
Papandreou, C. (2026). Brick calculator: bricks and mortar for a wall. Engineering Bible. https://engineeringbible.com/civil/brick-count/
Embed this calculator on your site
Copy this HTML into your page. The calculator stays free to use and links back here.