Skip to content
Engineering Bible

Results appear as you type. Use the arrow keys to move through them and Enter to open one.

Popular

↑ ↓ moveEnter openEsc close

Civil engineering formulas

The formulas behind the 30 civil calculators, on one page you can print or save as a PDF. Each block lists its variables and standard; the heading opens the calculator, with its assumptions and a worked example.

Concrete and masonry

Brick calculator: bricks and mortar for a wall

Bricks:

bricks per area = 1 / ((L + j) × (H + j))
bricks = A_net × bricks per area × wythes × (1 + waste)

Mortar, the method of BIA Technical Note 10:

mortar per brick = ((L + j) × (H + j) − L × H) × W
collar joint = A_net × j   (double wythe only)
  • L, H, W — specified length, height and width of the brick
  • j — mortar joint thickness, ⅜ in in the US and 10 mm in metric brickwork
  • A_net — wall area less doors and windows
  • wythes — one or two thicknesses of brick
BrickSize, inBricks per ft² with ⅜ in joints
Modular7⅝ × 2¼ × 3⅝6.86
Standard8 × 2¼ × 3⅝6.55
Queen7⅝ × 2¾ × 2¾5.76
Norman11⅝ × 2¼ × 3⅝4.57
Utility11⅝ × 3⅝ × 3⅝3.00

Concrete bag calculator

Bags for a volume:

bags = V × (1 + waste) / yield, rounded up

Yield of a bag of mass m, from 0.60 ft³ per 80 lb:

yield = m × 0.0075 ft³/lb

Common bag yields:

BagYieldBags per yd³Bags per m³
80 lb0.60 ft³ (17.0 L)4558.9
60 lb0.45 ft³ (12.7 L)6078.5
50 lb0.375 ft³ (10.6 L)7294.2
40 lb0.30 ft³ (8.5 L)90117.7
30 kg0.496 ft³ (14.0 L)54.471.2
25 kg0.413 ft³ (11.7 L)65.385.4
20 kg0.331 ft³ (9.4 L)81.6106.8

Concrete block calculator: CMU, mortar and grout

Blocks:

A_net = L × H − openings
blocks = A_net / (face length × face height) × (1 + waste)

Mortar and grout:

bags = blocks / 16
grout = A_net × g / 100
  • L, H — wall length and height; openings — area of doors and windows
  • face — nominal block face including one joint: 16 × 8 in (0.889 ft²) or 450 × 225 mm (0.101 m²)
  • 16 — blocks laid per 80 lb bag of preblended mortar with face-shell bedding (NCMA TEK 4-2A Table 2)
  • g — grout in ft³ per 100 ft² of wall from NCMA TEK 4-2A Table 3

Grout per 100 ft² of wall, two-core hollow units, 3 % waste included:

Cores grouted6 in wall8 in wall10 in wall12 in wall
Every core25.6 ft³36.1 ft³47.0 ft³58.9 ft³
16 in on centre12.8 ft³18.1 ft³23.5 ft³29.5 ft³
24 in on centre8.6 ft³12.1 ft³15.7 ft³19.7 ft³
32 in on centre6.4 ft³9.1 ft³11.8 ft³14.8 ft³
48 in on centre4.3 ft³6.1 ft³7.9 ft³9.9 ft³

Concrete column and post hole calculator

Round column or pier:

V = n × π × D² / 4 × H

Post hole, with the post standing on gravel:

V = n × (π × D² / 4 − A_post) × (h − h_gravel)
A_post = s² for a square post, π × s² / 4 for a round one

Order and bags:

V_order = V × (1 + waste)
bags = V_order / bag yield, rounded up
  • D — hole or column diameter; H — column height; h — hole depth
  • s — actual post size: a 4 × 4 is 3.5 in, a 6 × 6 is 5.5 in
  • n — number of holes or columns
  • bag yield — 0.60 ft³ per 80 lb, 0.45 ft³ per 60 lb, 0.30 ft³ per 40 lb, 11.7 L per 25 kg

Concrete footing calculator

Strip footing, measured along its centreline:

V = L_c × B × D

Pad footings, n of them:

V = n × L × B × D

Order volume and bags:

V_order = V × (1 + waste)
bags = V_order / bag yield, rounded up
  • L_c — centreline length; for a rectangle of outside size a × b, 2 × (a + b) − 4 × B
  • B — width of the footing; D — depth of concrete; L — length of one pad
  • waste — 10 % is usual when pouring into an earth trench
  • bag yield — 0.60 ft³ per 80 lb bag, 0.45 ft³ per 60 lb, 11.7 L per 25 kg

Concrete slab calculator

Volume of the slab and volume to order:

V = L × W × t × n
V_order = V × (1 + waste)

Unit conversions and bags:

cubic yards = cubic feet / 27
bags = V_order / bag yield, rounded up
  • L, W — length and width; t — thickness, with inches divided by 12 to get feet
  • n — number of identical slabs
  • waste — spillage and uneven ground allowance, 5 to 10 % for slabs
  • bag yield — 0.60 ft³ for 80 lb, 0.45 ft³ for 60 lb, 0.375 ft³ for 50 lb, 0.30 ft³ for 40 lb, 11.7 L for 25 kg

Concrete volume and rebar weight

Volumes:

Slab / footing:  V = L × W × t,    Wall:  V = L × H × t
Rectangular column:  V = b × d × H,    Round column:  V = π D² H / 4
V_net = V × count,    V_order = V_net (1 + waste),    m = ρ_concrete V_net

Nominal mix 1 : a : b by volume (dry-volume factor 1.54, cement bulk density 1 440 kg/m³):

dry volume = 1.54 V_order
cement volume = dry volume / (1 + a + b),    cement mass = cement volume × 1 440,    bags = mass / bag size
sand = a × cement volume,    aggregate = b × cement volume

Reinforcement:

bar mass per metre = 7 850 × π d²/4 ≈ d² / 162   (kg/m, d in mm)
Mesh: bars along A = floor(B / s) + 1, bars along B = floor(A / s) + 1, length per layer = (bars along A) A + (bars along B) B
Bars + links: main length = n × member length; link length = (floor(member length / s_link) + 1) × [2 (a − 2c) + 2 (b − 2c) + 20 d_link]
total = (main + links) × count × (1 + lap allowance)
steel ratio = steel mass / V_net

Typical steel ratios: slabs 80–120, walls 80–150, foundations 60–150, columns 150–300 kg/m³.

Site work and building

Asphalt calculator: tons of hot mix

Volume and weight:

V = L × W × t
m = V × ρ
m_order = m × (1 + waste)

Spread rate and the US rule of thumb:

spread [lb/yd²/in] = ρ [lb/ft³] × 9 / 12
tons = yd² × inches × 110 / 2 000
  • L, W — length and width of the paved area; t — compacted thickness
  • ρ — compacted density of the mix in place, 145 lb/ft³ (2.32 t/m³) by default
  • waste — allowance for edges, an uneven base and material left in the equipment
  • 1 short ton = 2 000 lb; 1 metric tonne = 1 000 kg = 2 205 lb

The rule of 110 lb per square yard per inch matches a density of 146.7 lb/ft³. At 145 lb/ft³ the spread rate is 108.75 lb per yd² per inch.

Earthwork cut and fill volumes

V_AEA = L (A₁ + A₂)/2
V_prismoidal = L (A₁ + 4 A_m + A₂)/6,   A_m measured or ≈ ((√A₁ + √A₂)/2)² for similar sections
correction = V_AEA − V_prismoidal
cut:   V_bank = V,   V_loose = V_bank (1 + swell),   V_compacted = V_bank (1 − shrinkage)
fill:  V_compacted = V,   V_bank = V/(1 − shrinkage),   V_loose = V_bank (1 + swell)
mass = V_bank ρ_bank,   ρ_loose = ρ_bank/(1 + swell),   loads = V_loose / truck capacity

Typical factors: sand and gravel swell 12 % / shrinkage 12 %; loam 25 % / 10 %; clay 33 % / 10 %; topsoil 25 % / 15 %; blasted rock swell 50 % and bulking 30 % when placed.

Gravel calculator: cubic yards and tons

Volume in place and volume to order:

V = L × W × d
V_order = V × (1 + c)

Weight, truck loads and cost:

m = V_order × ρ
loads = larger of V_order / truck volume and m / truck payload, rounded up
cost = tons × price per ton
  • L, W — length and width of the area; d — compacted depth, with inches divided by 12 to get feet
  • c — compaction and settlement allowance, as a fraction
  • ρ — loose bulk density of the delivered material
  • 1 yd³ = 27 ft³ = 0.7646 m³; 1 short ton = 2 000 lb = 907.2 kg

Loose bulk densities from the Caterpillar Performance Handbook:

Materialkg/m³lb/yd³short tons per yd³
Crushed stone1 6002 7001.35
Gravel, dry, ¼ to 2 in1 6902 8501.43
Sand and gravel, dry1 7202 9001.45
Sand, dry1 4202 4001.20
Topsoil9501 6000.80

Roof pitch calculator: rafters, area and shingles

Pitch, angle and multiplier:

s = pitch / 12 = tan θ
k = √(1 + s²)

Gable roof:

rafter = (span / 2 + eave overhang) × k
ridge height = (span / 2) × s
area = (span + 2 × eave) × (length + 2 × rake) × k
squares = area × (1 + waste) / 100 ft²
bundles = squares × 3, rounded up
  • pitch — rise in inches per 12 in of run; θ — roof angle; s — slope as a fraction
  • span — building width from wall to wall; length — along the ridge
  • eave, rake — horizontal overhangs at the eaves and at the gable ends
  • k — pitch multiplier, slope length per unit of horizontal run
PitchAngleMultiplier
4/1218.4°1.054
6/1226.6°1.118
8/1233.7°1.202
12/1245.0°1.414

Slope calculator: percent, degrees, ratio and pitch

From rise and run:

grade = rise / run                 percent = 100 × rise / run
θ = arctan(rise / run)
ratio 1 : n,  n = run / rise
pitch = 12 × rise / run            inches per foot
length along the slope = √(run² + rise²)
  • rise — vertical change; run — horizontal distance
  • θ — angle above the horizontal

Stair calculator: risers, treads and stringer

Risers, treads and run:

n = H / R_max, rounded up
R = H / n
treads = n − 1
run = treads × T

Stringer, angle and comfort:

stringer = √(H² + run²)
θ = atan(R / T)
comfort = 2R + T
  • H — total rise from finished floor to finished floor
  • R_max — the tallest riser you allow; R — the actual, equal riser height
  • T — tread depth, nosing to nosing
  • n — number of risers; the top riser lands on the upper floor, so there is one tread fewer

Code limits checked:

ItemIRC R311.7 (dwellings)IBC §1011 (other buildings)
Riser height7¾ in maximum4 to 7 in
Tread depth10 in minimum11 in minimum
Headroom6 ft 8 in80 in
Rise of one flight151 in12 ft

Trench and excavation volume calculator

Trench cross-section with side slopes n H : 1 V, and volumes:

A = (b + n d) × d
V_bank = A × L
V_loose = V_bank × (1 + swell)
loads = V_loose / truck capacity, rounded up
V_backfill = V_bank − π D² L / 4
  • b — bottom width; d — depth; L — length; n — horizontal run per unit of depth
  • OSHA maximum slopes: stable rock vertical, Type A ¾ : 1, Type B 1 : 1, Type C 1½ : 1
  • D — outside diameter of the pipe laid in the trench

Foundations and soils

Consolidation settlement calculator (clay layer)

Settlement, with σ'1 = σ'0 + Δσ:

normally consolidated:            S = Cc H/(1 + e0) log(σ'1/σ'0)
over-consolidated, σ'1 ≤ σ'p:     S = Cr H/(1 + e0) log(σ'1/σ'0)
over-consolidated, σ'1 > σ'p:     S = Cr H/(1 + e0) log(σ'p/σ'0) + Cc H/(1 + e0) log(σ'1/σ'p)

Rate of consolidation (Terzaghi):

T_v = c_v t / H_dr²
U = 1 − Σ (2/M²) exp(−M² T_v),   M = π(2m + 1)/2,  m = 0, 1, 2 …
T_v ≈ (π/4) U²  for U ≤ 60 %;    T_v ≈ 1.781 − 0.933 log(100 − U%)  for U > 60 %
  • H — layer thickness; e0 — initial void ratio; Cc, Cr — compression and recompression indices
  • σ'0 — present effective stress at mid-layer; σ'p — preconsolidation pressure; Δσ — stress increase
  • c_v — coefficient of consolidation; H_dr — drainage path, H/2 when both faces drain

Crane outrigger pad bearing pressure

F = manufacturer value,  or ≈ 0.65 × (crane + load + rigging) g,  or (crane + load + rigging) g
q_float = F / A_float
rigid mat:  q = (F + W_mat) / (L_mat B_mat),   bending σ = 3 q c² / t²,  c = largest overhang beyond the float
spread:     L_eff = min(L_mat, L_float + 2 t tan θ),  q = F / (L_eff B_eff) + W_mat / A_mat
required area = F / q_allow,   square side = √(F / q_allow)

BS 8004 presumed allowable values (lower bounds): rock 4 000, dense gravel 600, compact sand 300, very stiff clay 300, medium dense gravel 200, stiff clay 150, medium dense sand 100, firm clay 75 kPa; soft or loose ground must be tested.

Footing size calculator

Net allowable pressure and required area:

q_net = q_all − γ_c t − γ_s h_s
A = P / q_net

Plan dimensions:

square:     B = √A
round:      D = √(4A / π)
rectangle:  B = √(A / r),  L = r B
strip:      B = w / q_net

Actual pressure with the rounded size:

q = P / A_rounded + γ_c t + γ_s h_s
  • P — service (unfactored) column load; w — load per length of wall
  • q_all — allowable bearing pressure; t — footing thickness; h_s — soil above the footing
  • γ_c, γ_s — unit weights of concrete and soil; r — length to width ratio

Pile capacity calculator (driven and bored piles)

Ultimate and allowable capacity:

Q_ult = Q_s + Q_b = Σ f_i P Δz_i + q_b A_b
Q_all = Q_ult / FS

Driven piles (API RP 2GEO):

clay:  f = α s_u,  α = 0.5 ψ^−0.5 (ψ ≤ 1) or 0.5 ψ^−0.25 (ψ > 1),  α ≤ 1,  ψ = s_u / σ'v
       q_b = 9 s_u
sand:  f = β σ'v ≤ f_lim,   q_b = N_q σ'v ≤ q_lim   (dense sand: β 0.46, 96 kPa, N_q 40, 10 MPa)

Bored piles (O'Neill and Reese, FHWA 1999):

clay:  f = 0.55 s_u, none in the top 1.5 m and the bottom D;  q_b = 6 (1 + 0.2 L/D) s_u ≤ 9 s_u
sand:  f = β σ'v ≤ 200 kPa,  β = 1.5 − 0.245 √z  (0.25 to 1.2, z in m);  q_b = 57.5 N60 kPa
  • P — pile perimeter; A_b — base area; D — diameter; L — embedded length
  • s_u — undrained shear strength; σ'v — effective vertical stress; N60 — SPT blow count

Retaining wall earth pressure calculator (Rankine)

Earth pressure coefficients:

K_a = tan²(45° − φ/2)                         active, level backfill
K_a = cos β (cos β − √(cos²β − cos²φ)) / (cos β + √(cos²β − cos²φ))   sloping backfill
K_p = tan²(45° + φ/2)                         passive
K_0 = 1 − sin φ                                at rest (Jaky)

Thrust per metre of wall and its height above the base:

P = ½ K γ H² + K q H
ȳ = ( ½ K γ H² × H/3 + K q H × H/2 ) / P

Gravity wall of width b and weight W = γ_w b H:

FS_sliding = μ W / P_h,   FS_overturning = (W b / 2) / (P_h ȳ)
  • φ — friction angle of the backfill; γ — its unit weight; H — retained height
  • q — uniform surcharge; β — slope of the backfill; μ — friction between base and soil

Soil bearing capacity calculator (Terzaghi and Eurocode 7)

General form, for a footing of width B at depth D_f:

q_ult = c N_c s_c + q N_q s_q + ½ γ B N_γ s_γ,    q = γ D_f

Eurocode 7 Annex D factors (drained):

N_q = e^{π tan φ} tan²(45° + φ/2)
N_c = (N_q − 1) cot φ,    N_γ = 2 (N_q − 1) tan φ
s_q = 1 + (B/L) sin φ,    s_γ = 1 − 0.3 B/L,    s_c = (s_q N_q − 1)/(N_q − 1)

Undrained (clay, short term):

q_ult = (π + 2) c_u (1 + 0.2 B/L) + q

Terzaghi:

N_q = e^{2(3π/4 − φ/2) tan φ} / (2 cos²(45° + φ/2)),    N_c = (N_q − 1) cot φ
square: 1.3 c N_c + q N_q + 0.4 γ B N_γ;   circle: 1.3 c N_c + q N_q + 0.3 γ B N_γ
  • φ — friction angle; c — cohesion; c_u — undrained shear strength; γ — unit weight of the soil
  • Allowable pressure: q_all = q_ult / FS, with FS usually 2.5 to 3

Soil compaction calculator (Proctor relative compaction)

Dry density and relative compaction:

ρ_d = ρ / (1 + w)
RC = ρ_d / ρ_d,max × 100 %

Weight–volume relations:

e = G_s ρ_w / ρ_d − 1,    n = e / (1 + e)
S = w G_s / e
V_a = 1 − (ρ_d / ρ_w)(1/G_s + w)

Zero-air-voids density, the upper limit at moisture w:

ρ_zav = G_s ρ_w / (1 + w G_s)
  • ρ — wet (bulk) density; w — moisture content as a decimal
  • ρ_d,max — maximum dry density from the Proctor test
  • G_s — specific gravity of the soil solids; ρ_w = 1 000 kg/m³ = 62.43 lb/ft³

Surveying and roads

Closed traverse calculator (compass rule)

Latitude and departure of each leg, with the azimuth Az measured clockwise from north:

Lat = L × cos Az,    Dep = L × sin Az

Misclosure and precision:

e = √( (ΣLat)² + (ΣDep)² )
precision = 1 : (ΣL / e)

Compass (Bowditch) rule corrections for leg i:

C_lat,i = −ΣLat × L_i / ΣL,    C_dep,i = −ΣDep × L_i / ΣL
N_i+1 = N_i + Lat_i + C_lat,i,    E_i+1 = E_i + Dep_i + C_dep,i
  • L — horizontal length of a leg; ΣL — total length of the traverse
  • A bearing such as S 75°30′ E is the azimuth 180° − 75°30′ = 104°30′
  • The area of the adjusted polygon comes from the coordinate (shoelace) formula

Latitude/longitude to UTM converter (WGS84)

Ellipsoid and series constants (WGS84, a = 6 378 137 m, f = 1/298.257223563):

n = f / (2 − f),    e² = f (2 − f)
A = a / (1 + n) × (1 + n²/4 + n⁴/64 + n⁶/256)

Forward, with λ the longitude from the zone's central meridian:

τ = tan φ,   σ = sinh(e atanh(e τ / √(1 + τ²)))
τ′ = τ √(1 + σ²) − σ √(1 + τ²)
ξ′ = atan2(τ′, cos λ),    η′ = asinh(sin λ / √(τ′² + cos² λ))
ξ = ξ′ + Σ α_j sin(2jξ′) cosh(2jη′),    η = η′ + Σ α_j cos(2jξ′) sinh(2jη′)
E = 500 000 + k₀ A η,    N = k₀ A ξ  (+ 10 000 000 south of the equator)

Inverse: the same series with the β_j coefficients, then φ from τ′ by Newton's method.

  • φ — latitude; λ — longitude difference; k₀ = 0.9996 — scale on the central meridian
  • α_j, β_j — Krüger coefficients, polynomials in n up to n⁶ (Karney 2011)
  • Zone = floor((longitude + 180°) / 6°) + 1, with the Norway and Svalbard exceptions

Polygon area from coordinates (shoelace method)

Shoelace (Gauss) formula for n corners, with corner n + 1 equal to corner 1:

2A = Σ (x_i y_i+1 − x_i+1 y_i)
A = |2A| / 2

Perimeter and centroid:

P = Σ √( (x_i+1 − x_i)² + (y_i+1 − y_i)² )
C_x = Σ (x_i + x_i+1)(x_i y_i+1 − x_i+1 y_i) / (6 A_signed)
C_y = Σ (y_i + y_i+1)(x_i y_i+1 − x_i+1 y_i) / (6 A_signed)
  • x, y — easting and northing of each corner, in order round the boundary
  • A positive sum means counter-clockwise corners, a negative one clockwise
  • 1 acre = 43 560 ft² = 4 046.856 m²; 1 hectare = 10 000 m²

Vertical curve calculator (crest and sag)

Elevation at a distance x from the PVC on a curve of length L:

y = y_PVC + g1 x + (g2 − g1) x² / (2L)
y_PVC = y_PVI − g1 L/2,    y_PVT = y_PVI + g2 L/2

High or low point and the K value:

x_turn = −g1 L / (g2 − g1)
A = |g2 − g1| in %,    K = L / A

AASHTO sight distance S provided, in feet (metric constants in brackets):

crest, S < L:  L = A S² / 2158  [658]       S > L:  L = 2S − 2158/A  [658]
sag,   S < L:  L = A S² / (400 + 3.5 S)  [120 + 3.5 S]
stopping sight distance needed = 1.47 V t + 1.075 V²/a,  t = 2.5 s, a = 11.2 ft/s²
  • g1, g2 — grades in and out, as decimals in the elevation formula
  • Stations increase in the direction of travel; 25+60 means 2 560 ft
  • V — design speed in mph; the metric form is 0.278 V t + 0.039 V²/a with V in km/h and a = 3.4 m/s²

Drainage and hydraulics

Culvert capacity and headwater calculator (HDS-5)

Inlet control, HDS-5 Appendix A, with D in ft and Q in ft³/s:

unsubmerged (Q/AD^0.5 ≤ 3.5):  HW/D = Hc/D + K (Q / A D^0.5)^M − 0.5 S
submerged   (Q/AD^0.5 ≥ 4.0):  HW/D = c (Q / A D^0.5)² + Y − 0.5 S

Outlet control with the barrel flowing full, HDS-5 chapter 3:

H = [1 + ke + 29 n² L / R^1.33] × V² / 2g
HW = H + h_o − L S,   h_o = max(TW, (d_c + D) / 2)
  • D — pipe diameter or box rise; A — full barrel area; S — barrel slope
  • Hc — specific head at critical depth, d_c + V_c²/2g; between 3.5 and 4.0 the result is interpolated
  • K, M, c, Y — inlet constants of HDS-5 Table A.1; ke — entrance loss coefficient of Table C.2
  • n — Manning roughness; L — barrel length; R — hydraulic radius; V = Q / A
  • TW — tailwater depth above the outlet invert; d_c — critical depth
InletKMcYke
Pipe, square edge with headwall0.00982.00.03980.670.5
Pipe, groove end with headwall0.00182.00.02920.740.2
Pipe, groove end projecting0.00452.00.03170.690.2
Box, wingwalls 30° to 75°0.0261.00.03470.810.4
Box, wingwalls 90° or 15°0.0610.750.04000.800.5
Box, wingwalls 0°0.0610.750.04230.820.7

Drain pipe size calculator (Manning)

Manning's equation for a pipe flowing full:

V = (1/n) × R^(2/3) × S^(1/2)        (SI, metres)
V = (1.486/n) × R^(2/3) × S^(1/2)    (US, feet)
Q = A × V,  A = π D² / 4,  R = D / 4

Part-full pipe at depth y, and the minimum slope:

θ = 2 acos(1 − 2y/D)
A = D² (θ − sin θ) / 8,  P = D θ / 2,  R = A / P
S_min = (n × V_min / R^(2/3))²
  • D — inside diameter; S — slope as a fraction, 1 % = 0.01
  • n — Manning roughness: 0.009 for smooth PVC, 0.013 for concrete and clay, and for any pipe where the agency requires it
  • V_min — self-cleansing velocity, 2.0 ft/s (0.61 m/s) flowing full
  • A, P, R — flow area, wetted perimeter and hydraulic radius

Open-channel flow (Manning)

Section geometry (depth y):

Rectangular:  A = b y,            P = b + 2y,                 T = b
Trapezoidal:  A = (b + z y) y,    P = b + 2y √(1 + z²),       T = b + 2 z y
Triangular:   A = z y²,           P = 2y √(1 + z²),           T = 2 z y
Circular:     θ = 2 acos(1 − 2y/D),  A = D² (θ − sin θ)/8,  P = D θ/2,  T = D sin(θ/2)
R = A / P

Manning (SI):

V = (1/n) R^(2/3) S^(1/2),    Q = A V

Normal depth: the y for which A V = Q (bisection). Circular pipes carry their maximum free-surface discharge at about 94 % depth; above that the capacity falls back to the full-pipe value.

Critical flow and energy:

Fr = V / √(g A/T)       (< 1 subcritical, > 1 supercritical)
critical depth y_c:  Q² T / (g A³) = 1   (rectangle: y_c = (q²/g)^(1/3), q = Q/b)
E = y + V² / (2g)
τ₀ = ρ g R S

Manning n (Chow, normal values): PVC 0.009; coated steel 0.012; finished concrete 0.013; rough concrete 0.017; corrugated metal 0.024; clean earth 0.022; weedy earth 0.030; gravel 0.025; riprap 0.035; natural clean stream 0.030; weedy stream 0.050.

Rational-method runoff

C = Σ C_k A_k / Σ A_k                    composite runoff coefficient
t_c = 0.0195 L^0.77 S^−0.385  [min]      Kirpich (L m, S m/m); design duration = max(t_c, minimum)
i = a / (t_c + b)^n                       optional IDF fit (mm/h), else the IDF-curve value at t_c
Q = C C_f i A / 360   [m³/s]              i mm/h, A ha, C C_f ≤ 1
depth = C C_f i t_c,   volume = depth × A

Runoff coefficients (2–10 year storms): roofs 0.90, pavement 0.85, industrial 0.75, gravel 0.50, residential 0.40, lawns 0.10–0.30, woodland 0.15. Frequency factor C_f: 1.0 up to 10 years, 1.1 (25), 1.2 (50), 1.25 (100).

Weir and flume flow calculator

Sharp-crested weirs, head H and crest length L in feet, flow in ft³/s:

rectangular (Francis):   Q = 3.33 (L − 0.1 n H) H^1.5
90° V-notch (Cone):      Q = 2.49 H^2.48
Cipolletti:              Q = 3.367 L H^1.5

Parshall flume, upstream head H_a in feet:

Q = C × H_a^n                      (1 in to 1 ft, USBR Table 8-6)
Q = 4 W × H_a^(1.522 W^0.026)      (2 to 8 ft)
  • n — number of end contractions: 2 for a notch narrower than the channel, 0 for a suppressed weir across the full width
  • W — throat width of the flume in feet
  • C, n — 0.338 and 1.55 for 1 in; 0.676 and 1.55 for 2 in; 0.992 and 1.55 for 3 in; 2.06 and 1.58 for 6 in; 3.07 and 1.53 for 9 in; 3.95 and 1.55 for 1 ft
  • metric inputs are converted to feet; 1 ft³/s = 28.32 L/s = 448.8 US gpm

Results are estimates. They do not replace the governing code, class or flag requirements, or a check by a competent person.