How to calculate a ship's CII rating, step by step
The Carbon Intensity Indicator (CII) is the IMO's yearly measure of how much CO₂ a ship emits for the transport capacity it moves. Since 2023 every cargo, ro-ro and cruise ship of 5 000 GT and above receives a rating from A to E under MARPOL Annex VI regulation 28, based on the fuel and distance it reports to the IMO Data Collection System (DCS). The verified rating is issued by the Administration or a recognised organisation; what you calculate yourself is an estimate of it, and a useful one, because the arithmetic is short and fully published.
The calculation has four links: the attained CII from the year's fuel and distance, a reference line for the ship type and size, a reduction factor that tightens the requirement every year, and four boundaries around the required value that decide the letter. This guide goes through each link with the coefficients from the IMO guidelines, works one ship through in full, and then shows how speed and waiting time move the result. The CII rating estimator reproduces every number.
What you need before you start
Four things, all from documents the ship already has:
- Ship type as defined in MARPOL Annex VI regulation 2. The type selects the reference line and the rating boundaries.
- Capacity. Deadweight (DWT) for bulk carriers, tankers, container ships, gas and LNG carriers, general cargo ships, refrigerated cargo carriers and combination carriers; gross tonnage (GT) for ro-ro ships and cruise passenger ships. Use the deadweight at the summer load line from the ship's certificates, not the cargo actually carried.
- Fuel consumed in the calendar year, by fuel type, in tonnes, as reported to the DCS. All fuel counts: main engine, auxiliaries, boilers, at sea, at anchor and in port.
- Distance travelled in the year, in nautical miles over ground, ballast legs included.
Step 1: the attained CII
The attained CII follows IMO Resolution MEPC.352(78), the G1 guidelines. It is the mass of CO₂ in grams divided by capacity and distance:
CII_attained = Σ(FC_j × C_F,j) × 10⁶ ÷ (Capacity × D_t) [g CO₂ per capacity·nmi]
FC_j is the mass of fuel j in tonnes, C_F,j its carbon factor in tonnes of CO₂ per tonne of fuel, and D_t the distance in nautical miles. The carbon factors are those of MEPC.364(79), Table 1:
| Fuel | C_F, t CO₂ per t fuel |
|---|---|
| HFO | 3.114 |
| LFO / VLSFO | 3.151 |
| MGO / MDO | 3.206 |
| LNG | 2.750 |
| LPG (propane) | 3.000 |
| LPG (butane) | 3.030 |
| Methanol | 1.375 |
These are tank-to-wake factors for CO₂ only, fixed per fuel grade. The fuel specific energy and CO₂ factor calculator shows where they come from (a typical carbon content for each grade) and how a measured carbon content would differ; for the CII you use the grade value.
Step 2: the reference line and the required CII
The reference line of MEPC.353(78) (G2) is a curve fitted for each ship type to 2019 performance, with capacity as the only variable:
CII_ref = a × Capacity^(−c)
The required CII for a given year is the reference value lowered by the reduction factor Z of that year:
CII_required = (1 − Z ÷ 100) × CII_ref
| Year | 2023 | 2024 | 2025 | 2026 | 2027 | 2028 | 2029 | 2030 |
|---|---|---|---|---|---|---|---|---|
| Z, % | 5 | 7 | 9 | 11 | 13.625 | 16.25 | 18.875 | 21.5 |
The factors for 2023 to 2026 come from MEPC.338(76) and those for 2027 to 2030 from MEPC.400(83), adopted on 11 April 2025. Nothing is set beyond 2030.
Step 3: the rating boundaries
MEPC.354(78) (G4) places four boundaries around the required CII. Each is the required value multiplied by a factor exp(d) that depends on the ship type:
A/B = exp(d1) × CII_required B/C = exp(d2) × CII_required
C/D = exp(d3) × CII_required D/E = exp(d4) × CII_required
Below the A/B boundary the ship is rated A, between A/B and B/C it is B, and so on; above D/E it is E. A rating of C means roughly "at the required level": the C band always contains the required value itself. The table gives the reference-line parameters and the four exp(d) factors together.
| Ship type and size | Capacity in the reference line | a | c | exp(d1) / exp(d2) / exp(d3) / exp(d4) |
|---|---|---|---|---|
| Bulk carrier | DWT, capped at 279 000 | 4745 | 0.622 | 0.86 / 0.94 / 1.06 / 1.18 |
| Gas carrier, 65 000 DWT and above | DWT | 14405 × 10⁷ | 2.071 | 0.81 / 0.91 / 1.12 / 1.44 |
| Gas carrier, below 65 000 DWT | DWT | 8104 | 0.639 | 0.85 / 0.95 / 1.06 / 1.25 |
| Tanker | DWT | 5247 | 0.610 | 0.82 / 0.93 / 1.08 / 1.28 |
| Container ship | DWT | 1984 | 0.489 | 0.83 / 0.94 / 1.07 / 1.19 |
| General cargo, 20 000 DWT and above | DWT | 31948 | 0.792 | 0.83 / 0.94 / 1.06 / 1.19 |
| General cargo, below 20 000 DWT | DWT | 588 | 0.3885 | 0.83 / 0.94 / 1.06 / 1.19 |
| Refrigerated cargo carrier | DWT | 4600 | 0.557 | 0.78 / 0.91 / 1.07 / 1.20 |
| Combination carrier | DWT | 5119 | 0.622 | 0.87 / 0.96 / 1.06 / 1.14 |
| LNG carrier, 100 000 DWT and above | DWT | 9.827 | 0 | 0.89 / 0.98 / 1.06 / 1.13 |
| LNG carrier, 65 000 to 100 000 DWT | DWT | 14479 × 10¹⁰ | 2.673 | 0.78 / 0.92 / 1.10 / 1.37 |
| LNG carrier, below 65 000 DWT | 65 000 | 14779 × 10¹⁰ | 2.673 | 0.78 / 0.92 / 1.10 / 1.37 |
| Ro-ro vehicle carrier, 57 700 GT and above | 57 700 | 3627 | 0.590 | 0.86 / 0.94 / 1.06 / 1.16 |
| Ro-ro vehicle carrier, 30 000 to 57 700 GT | GT | 3627 | 0.590 | 0.86 / 0.94 / 1.06 / 1.16 |
| Ro-ro vehicle carrier, below 30 000 GT | GT | 330 | 0.329 | 0.86 / 0.94 / 1.06 / 1.16 |
| Ro-ro cargo ship | GT | 1967 | 0.485 | 0.76 / 0.89 / 1.08 / 1.27 |
| Ro-ro passenger ship | GT | 2023 | 0.460 | 0.76 / 0.92 / 1.14 / 1.30 |
| Ro-ro passenger ship, high-speed craft | GT | 4196 | 0.460 | 0.76 / 0.92 / 1.14 / 1.30 |
| Cruise passenger ship | GT | 930 | 0.383 | 0.87 / 0.95 / 1.06 / 1.16 |
The caps and floors in the second column (279 000 DWT for bulk carriers, 65 000 DWT for small LNG carriers, 57 700 GT for vehicle carriers) apply to the reference line only. The attained CII always uses the ship's real capacity.
Worked example: an 82 000 DWT bulk carrier in 2026
A bulk carrier of 82 000 DWT sails 62 000 nmi in 2026 at an average of 12.5 knots. That is 206.7 days at sea; the remaining 158.3 days are spent in port and at anchor. The main engine burns 25 t/day at sea and the auxiliaries 2.5 t/day, both on VLSFO; in port and at anchor the ship burns 3.5 t/day of MGO. The fuel consumption and voyage cost calculator turns that profile into 5 167 t for the main engine, 517 t for the auxiliaries at sea and 554 t in port, so the year's DCS figures are 5 683 t of VLSFO and 554 t of MGO.
- CO₂. 5 683 × 3.151 = 17 907 t from VLSFO and 554 × 3.206 = 1 776 t from MGO: 19 683 t in total.
- Attained CII. 19 683 × 10⁶ ÷ (82 000 × 62 000) = 3.872 g CO₂/(DWT·nmi).
- Reference CII. 4745 × 82 000^(−0.622) = 4.167.
- Required CII for 2026 (Z = 11 %). 0.89 × 4.167 = 3.709.
- Boundaries. A/B 0.86 × 3.709 = 3.190; B/C 0.94 × 3.709 = 3.486; C/D 1.06 × 3.709 = 3.931; D/E 1.18 × 3.709 = 4.376.
- Rating. 3.872 lies between 3.486 and 3.931: the ship is rated C, with the attained value 4.4 % above the required one.
- Margin. The most CO₂ the ship could emit over this distance and stay in C is 3.931 × 82 000 × 62 000 ÷ 10⁶ = 19 987 t. The margin is 304 t of CO₂, or 1.5 % of the C/D boundary: about 96 t of VLSFO over a whole year.
Enter the same figures in the CII rating estimator (bulk carrier, 82 000 DWT, 2026, 62 000 nmi, 5 683 t VLSFO, 554 t MGO, no HFO) and it returns these values.
Now keep the ship's performance exactly as it is and let the years pass. The attained value stays at 3.872, but the boundaries move down:
| Year | Required CII | C/D boundary | D/E boundary | Rating at 3.872 |
|---|---|---|---|---|
| 2026 | 3.709 | 3.931 | 4.376 | C |
| 2027 | 3.599 | 3.815 | 4.247 | D |
| 2028 | 3.490 | 3.699 | 4.118 | D |
| 2029 | 3.381 | 3.583 | 3.989 | D |
| 2030 | 3.271 | 3.468 | 3.860 | E |
A ship that does nothing slides from C to E in four years. That is the design of the scheme, not an accident of this example.
How speed and idle time move the rating
Two operating variables dominate the attained CII: the speed at sea and the share of the year spent not moving.
Speed
Near the design speed, main-engine fuel per day rises roughly with the cube of speed, so fuel per mile rises with the square. Take the same ship over the same 62 000 nmi at 11.5 knots instead of 12.5. The cube law gives 25 × (11.5 ÷ 12.5)³ = 19.5 t/day for the main engine. The passage now takes 224.6 sea days, so the main engine burns 4 373 t and the auxiliaries 562 t (more than before, because they run for more days at sea); port time falls to 140.4 days and 491 t of MGO. With 4 935 t of VLSFO and 491 t of MGO the CO₂ is 17 124 t and the attained CII 3.368: rating B, a 13 % improvement from an 8 % speed reduction.
The cube law is an approximation that holds near the speed it was fitted to. At very low speeds the auxiliary and hotel loads take over and fuel per mile rises again, and the extra days have a commercial cost that the CII does not see. The optimal speed under charter calculator finds the speed that is cheapest once hire and fuel are both counted; its model does not price the rating, so treat the two answers as separate constraints.
Waiting
Waiting adds CO₂ without adding distance. Suppose the same ship at 12.5 knots loses 25 sailing days to waiting at anchor. Distance falls to 54 500 nmi, sea days to 181.7 and port and anchorage days rise to 183.3. Fuel becomes 4 996 t of VLSFO and 642 t of MGO. Total CO₂ falls to 17 801 t, yet the attained CII rises to 3.983, above the C/D boundary of 3.931: rating D. The ship emitted less and rated worse, because the divisor shrank faster than the emissions.
Hull and propeller condition
Fouling raises main-engine fuel at the same speed and distance. In the example the main engine produces 5 167 × 3.151 = 16 280 t of the 19 683 t of CO₂, about 83 %, so every 1 % of added main-engine fuel adds about 0.83 % to the attained CII. A fouling penalty of 2 % is therefore more than the whole 1.5 % margin of the example ship. The hull cleaning interval calculator weighs the fuel penalty against the cost of cleaning; it does not price the rating either, so shorten the interval when a band is at stake.
What a D or E rating triggers
A poor rating does not by itself stop the ship from trading. Under MARPOL Annex VI regulation 28, a ship rated D for three consecutive years, or E in a single year, must include a corrective action plan in Part III of its SEEMP, and that plan has to be verified. In the table above, the unchanged ship would need a corrective action plan after its third D year, 2029, and again for the E of 2030.
The commercial effect usually arrives sooner than the regulatory one: charterers increasingly write rating clauses into charter parties, and a D or E ship is harder to fix.
Common mistakes
- Wrong capacity basis. GT for a bulk carrier or DWT for a ro-ro ship gives a meaningless number. So does the cargo carried: the CII uses the certified capacity whether the ship is full, part-loaded or in ballast.
- Wrong deadweight. Capacity sits on both sides of the comparison. Enter 75 000 t instead of 82 000 t for the example ship and the attained CII becomes 4.233 against a C/D boundary of 4.156, a D instead of a C.
- Capping the capacity in the attained CII. The caps and floors belong to the reference line only.
- Distance through water or laden distance only. The DCS distance is over ground and includes ballast legs. Leaving out the ballast legs makes the ship look far worse than it is.
- One carbon factor for all fuel. Multiply each fuel by its own C_F. MGO burned in port carries 3.206, not the 3.151 of the VLSFO burned at sea.
- Leaving out port and anchorage fuel. Boilers and generators at anchor count in full, with zero distance against them.
- Part-year data. The rating is for a calendar year. A mid-year check is valid only as "the rating if the rest of the year looks like this"; a distance below about 10 000 nmi for an ocean-going ship usually means the figures do not cover the full year.
- Using last year's reduction factor. Z changes every year, and from 2027 it steps by 2.625 points a year instead of 2.
- Expecting your figure to match the class society's when corrections apply. See the next section.
Limits of the method
The method above is the basic regulatory calculation. It leaves out the voyage adjustments and correction factors of MEPC.355(78), the G5 guidelines: ice-class ships, shuttle tankers, ship-to-ship operations, electrical cargo consumers and excluded voyage segments. Those corrections can only lower the attained CII, so for a ship entitled to them the basic figure is conservative, and it will differ from the verified one.
Other points to keep in mind:
- The LNG carrier reference line is discontinuous at 65 000 DWT, because the guideline prints different values of a for the two rows. The table reproduces them as printed.
- A value exactly on a boundary falls in the better band. At realistic precision this never decides a rating.
- The EEXI is a separate, one-off design certificate and plays no part in the annual rating.
- The CII counts CO₂ from combustion only, with the IMO carbon factors. The European regimes use different quantities: the EU ETS prices tonnes of CO₂-equivalent on EEA voyages, and FuelEU Maritime limits well-to-wake intensity per unit of energy. A ship can do well on one and badly on another; the guide to EU ETS and FuelEU costs and the EU ETS and FuelEU Maritime calculator cover those.
The governing texts are MARPOL Annex VI regulation 28 and the IMO resolutions named above: MEPC.352(78) for the attained CII, MEPC.353(78) for the reference lines, MEPC.338(76) and MEPC.400(83) for the reduction factors, MEPC.354(78) for the rating and MEPC.355(78) for the corrections.
Calculators used in this guide
- MaritimeCII rating estimatorAttained and required operational CII with the A–E rating, from ship type, capacity, annual fuel or CO₂ and distance.
- MaritimeFuel consumption and voyage costFuel burned, time at sea, bunker cost and CO₂ for a passage from distance, speed and engine power or daily consumption.
- MaritimeFuel net specific energy and CO₂ factorISO 8217 net and gross specific energy from density, water, ash and sulphur; CO₂ factor by IMO grade or carbon content; g CO₂/MJ.
- MaritimeOptimal speed under charterCost-minimising speed on time charter and profit-maximising speed on a voyage charter from the fuel-speed law, prices, hire or freight and port time.
- MaritimeOptimal hull cleaning intervalCleaning interval that minimises fuel penalty plus cleaning cost, from the fouling growth rate, fuel and ETS prices and the cost per cleaning.
- MaritimeEU ETS and FuelEU MaritimeEU ETS allowances and cost with phase-in and voyage scope; FuelEU Maritime GHG intensity against the yearly limit, compliance balance and penalty.
Results are estimates. They do not replace the governing code, class or flag requirements, or a check by a competent person. Report an error in this guide
More guides
- Cargo securing calculation to CSS Code Annex 13
- How to do a draft survey calculation, step by step
- How EU ETS and FuelEU Maritime costs are calculated
- Hull and propeller performance in service with ISO 19030
- Ship resistance and powering: from hull to installed power
- How to calculate ship squat and under-keel clearance