Mechanical engineering practice problems
10 multiple-choice problems in the style of the FE and PE engineering exams. Pick an answer to check it, then open the worked solution. Every answer is recomputed by the mechanical calculator that solves it, and the solution opens that calculator with the problem's numbers filled in.
-
Rating life of a deep-groove ball bearing under combined load
A deep-groove ball bearing on a conveyor drive shaft has a basic dynamic load rating C of 30.7 kN. It carries a radial load of 3.2 kN and an axial load of 1.4 kN at 1200 rpm. From the catalogue, e = 0.28, X = 0.56 and Y = 1.55 when Fa/Fr > e. Take the application factor as 1.0. What is the basic rating life L10 in operating hours?
Show the answer and worked solution
Answer: C, 6460 h
- Load ratio: Fa/Fr = 1.4 / 3.2 = 0.44, which is above e = 0.28, so the axial load counts.
- Equivalent load: P = X Fr + Y Fa = 0.56 × 3.2 + 1.55 × 1.4 = 3.96 kN.
- Life in revolutions: L10 = (C/P)³ = (30.7 / 3.962)³ = 465 million revolutions (exponent 3 for ball bearings).
- Life in hours: L10h = 465 × 10⁶ / (60 × 1200) = 6460 h.
- The traps: 12 300 h uses the radial load alone as P, 4130 h adds the loads directly (P = Fr + Fa = 4.6 kN), and 12 800 h uses the roller bearing exponent 10/3.
Check every step: Rolling bearing L10 life (ISO 281), opened with this problem’s numbers
-
Pulling force of a hydraulic cylinder on the retract stroke
A double-acting hydraulic cylinder has an 80 mm bore and a 45 mm rod. It works at a pressure of 160 bar, and seal friction gives a force efficiency of 95 %. The cylinder retracts to pull a sluice gate closed. What pulling force does the rod deliver on the retract stroke?
Show the answer and worked solution
Answer: D, 52.2 kN
- Annulus area: A = π/4 (D² − d²) = π/4 (0.080² − 0.045²) = 3.436 × 10⁻³ m².
- Pull force: F = p A η = 16 × 10⁶ × 3.436 × 10⁻³ × 0.95 = 52.2 kN.
- The traps: 76.4 kN uses the full bore area (that is the push force), 55.0 kN leaves out the 95 % efficiency, and 24.2 kN uses the rod area instead of the annulus.
Check every step: Hydraulic cylinder force and speed, opened with this problem’s numbers
-
Shaft diameter set by shear stress and angle of twist
A solid steel shaft 1.5 m long transmits 22 kW at 960 rpm. The allowable shear stress is 40 MPa, and the angle of twist over the full 1.5 m length must not exceed 1°. The shear modulus is G = 80 GPa. What is the minimum shaft diameter that meets both limits?
Show the answer and worked solution
Answer: B, 39.3 mm
- Torque: T = P/ω = 22 000 / (960 × 2π/60) = 218.8 N·m.
- Stress limit: d = (16 T / (π τ))^(1/3) = (16 × 218.8 / (π × 40 × 10⁶))^(1/3) = 30.3 mm.
- Twist limit: θ = 1° = 0.01745 rad, d = (32 T L / (π G θ))^(1/4) = (32 × 218.8 × 1.5 / (π × 80 × 10⁹ × 0.01745))^(1/4) = 39.3 mm.
- The larger diameter governs: d = 39.3 mm, so stiffness, not strength, sets the size.
- The traps: 30.3 mm checks only the shear stress, 33.1 mm uses I = π d⁴/64 in place of the polar moment J = π d⁴/32, and 35.5 mm applies the 1° limit to 1 m instead of the full 1.5 m.
Check every step: Shaft torsion calculator (shear stress, twist, diameter), opened with this problem’s numbers
-
Required shell thickness of an air receiver (ASME UG-27)
A cylindrical air receiver has an inside diameter of 1.8 m and a design pressure of 1.6 MPa. The shell material has an allowable stress of 138 MPa, the longitudinal seam is spot radiographed (joint efficiency E = 0.85) and a 3 mm corrosion allowance is required. Using the ASME VIII Division 1 UG-27 circumferential stress formula, what is the minimum required shell thickness including the corrosion allowance?
Show the answer and worked solution
Answer: A, 15.4 mm
- Inside radius: R = 1.8 / 2 = 0.9 m.
- UG-27: t = P R / (S E − 0.6 P) = 1.6 × 0.9 / (138 × 0.85 − 0.6 × 1.6) = 1.44 / 116.34 = 0.01238 m = 12.4 mm.
- Add the corrosion allowance: t = 12.4 + 3 = 15.4 mm.
- The traps: 13.5 mm takes E = 1.0 (full radiography), 12.4 mm forgets the corrosion allowance, and 27.8 mm puts the diameter in place of the radius.
Check every step: Thin-wall pressure vessel, opened with this problem’s numbers
-
Mass of a solid disc flywheel for a punch press
A punch press flywheel must absorb an energy fluctuation of 4.5 kJ per stroke while its speed stays within ±2 % of the mean speed of 240 rpm, so the coefficient of speed fluctuation is 0.04. The flywheel is a solid steel disc with an outer radius of 0.6 m. What disc mass is needed?
Show the answer and worked solution
Answer: C, 989 kg
- Mean angular speed: ω = 240 × 2π/60 = 25.13 rad/s.
- Required inertia: ΔE = I Cs ω², so I = 4500 / (0.04 × 25.13²) = 178.1 kg·m².
- Solid disc: I = m r²/2, so m = 2 I / r² = 2 × 178.1 / 0.6² = 989 kg.
- The traps: 495 kg uses the thin rim formula I = m r², 1980 kg takes Cs as 0.02 (only the +2 % half of the band), and 247 kg uses the 1.2 m diameter as the radius.
Check every step: Flywheel energy calculator (inertia and speed fluctuation), opened with this problem’s numbers
-
Von Mises stress at a point in plane stress
At a critical point on a machine bracket the plane stresses are σx = 90 MPa in tension, σy = 30 MPa in compression and τxy = 40 MPa. What is the von Mises equivalent stress at the point?
Show the answer and worked solution
Answer: B, 128 MPa
- Plane stress von Mises: σ_vm = √(σx² − σx σy + σy² + 3 τxy²).
- Substitute σy = −30 MPa: σ_vm = √(90² − 90 × (−30) + 30² + 3 × 40²) = √16 500 = 128 MPa.
- Check with the principal stresses: centre 30 MPa, radius √(60² + 40²) = 72.1 MPa, σ1 = 102 MPa, σ2 = −42.1 MPa, and √(σ1² − σ1 σ2 + σ2²) = 128 MPa.
- The traps: 102 MPa is the major principal stress alone, 115 MPa drops the factor 3 on τxy², and 144 MPa is the Tresca stress σ1 − σ2.
Check every step: Mohr's circle calculator (principal stress, von Mises), opened with this problem’s numbers
-
Leg tension in a four-leg chain sling
A 12 t skid is lifted with a four-leg chain sling. Each leg makes 40° with the vertical. The skid is rigid, so following the usual rule only three legs are assumed to carry the load. A dynamic factor of 1.15 is applied to the hook load. Take g = 9.81 m/s². What is the design tension in each loaded leg?
Show the answer and worked solution
Answer: D, 58.9 kN
- Hook load: W = 12 000 × 9.81 × 1.15 = 135.3 kN.
- Leg tension: T = W / (n cos θ) = 135.3 / (3 × cos 40°) = 58.9 kN.
- The traps: 44.2 kN shares the load over all four legs, 70.2 kN measures the 40° from the horizontal (cos 50°), and 51.2 kN leaves out the dynamic factor.
Check every step: Lifting sling and wire rope load, opened with this problem’s numbers
-
Output torque of a two-stage gear reducer
A two-stage spur gear reducer is driven by a motor delivering 49 N·m at 1460 rpm. Stage 1 has a 19-tooth pinion driving a 57-tooth wheel, and stage 2 has a 17-tooth pinion driving a 68-tooth wheel. Each stage has an efficiency of 97 %. What torque is available at the output shaft?
Show the answer and worked solution
Answer: A, 553 N·m
- Overall ratio: i = (57/19) × (68/17) = 3 × 4 = 12.
- Overall efficiency: η = 0.97² = 0.941.
- Output torque: T_out = T_in i η = 49 × 12 × 0.941 = 553 N·m.
- The traps: 588 N·m ignores the losses, 570 N·m applies the 97 % only once, and 323 N·m adds the stage ratios (3 + 4 = 7) instead of multiplying them.
Check every step: Gear ratio, rpm and torque, opened with this problem’s numbers
-
Rate of a helical compression spring with squared and ground ends
A helical compression spring is wound from 4 mm steel wire with an outside coil diameter of 32 mm. It has 10 total coils with squared and ground ends and a free length of 70 mm. The shear modulus of the wire is 79.3 GPa. What is the spring rate?
Show the answer and worked solution
Answer: D, 14.4 N/mm
- Mean coil diameter: D = 32 − 4 = 28 mm.
- Active coils: squared and ground ends have two inactive coils, so Na = 10 − 2 = 8.
- Rate: k = G d⁴ / (8 D³ Na) = 79 300 × 4⁴ / (8 × 28³ × 8) = 14.4 N/mm.
- The traps: 9.7 N/mm uses the 32 mm outside diameter as D, 11.6 N/mm counts all 10 coils as active, and 12.8 N/mm takes 9 active coils (the rule for plain ground ends).
Check every step: Spring rate calculator (helical compression spring), opened with this problem’s numbers
-
Length of an open flat belt between two pulleys
An open flat-belt drive connects a 100 mm motor pulley to a 400 mm fan pulley. The shaft centres are 400 mm apart and the motor runs at 1450 rpm. What belt length is needed?
Show the answer and worked solution
Answer: B, 1640 mm
- Open belt length: L = 2C + π (D + d)/2 + (D − d)²/(4C).
- L = 2 × 400 + π × 500/2 + 300²/(4 × 400) = 800 + 785.4 + 56.3 = 1642 mm.
- The exact formula with the wrap angles gives 1642 mm as well, so L ≈ 1640 mm.
- The traps: 1590 mm leaves out the (D − d)²/(4C) term, 1740 mm uses the crossed-belt term (D + d)²/(4C), and 1810 mm divides by C instead of 4C.
Check every step: Belt and pulley calculator (ratio, rpm, belt length), opened with this problem’s numbers
Results are estimates. They do not replace the governing code, class or flag requirements, or a check by a competent person.