Skip to content
Engineering Bible

Results appear as you type. Use the arrow keys to move through them and Enter to open one.

Popular

↑ ↓ moveEnter openEsc close

Gross and net tonnage calculator (ITC 1969)

Gross tonnage GT = K1 V and net tonnage NT by the 1969 Tonnage Convention (Annex I, regulations 3 and 4), with the convention's limits applied.

Units

Results are estimates. They do not replace the governing code, class or flag requirements, or a check by a competent person. Report a problem

Introduction

Gross tonnage is a measure of a ship's overall size, worked out from the volume of all its enclosed spaces. The 1969 Tonnage Convention defines it as GT = K1 V, where V is the total enclosed volume in cubic metres and K1 = 0.2 + 0.02 log10 V. A ship with 30 000 m³ of enclosed space has K1 = 0.28954 and a gross tonnage of 8 686. Net tonnage measures the useful capacity: the cargo spaces, corrected for draught, plus a term for passengers.

This calculator applies regulations 3 and 4 of Annex I of the convention to volumes you already have: the total enclosed volume, the cargo space volume, the moulded depth and draught, and the passenger numbers. It applies the convention's limits and says which ones bite. It is for superintendents, ship registrars, students and anyone checking tonnage-based fees or rule thresholds.

Formulas

Gross tonnage (regulation 3):

GT = K1 V,      K1 = 0.2 + 0.02 log10 V

Net tonnage (regulation 4):

NT = K2 Vc (4d / 3D)² + K3 (N1 + N2 / 10)
K2 = 0.2 + 0.02 log10 Vc,      K3 = 1.25 (GT + 10 000) / 10 000

Limits of regulation 4(1):

(4d / 3D)² ≤ 1,      K2 Vc (4d / 3D)² ≥ 0.25 GT,      NT ≥ 0.30 GT
N1 = N2 = 0 when N1 + N2 < 13
  • V — total volume of all enclosed spaces, m³; Vc — total volume of cargo spaces, m³
  • D — moulded depth amidships; d — moulded draught amidships as regulation 4(2) defines it
  • N1 — passengers in cabins with not more than 8 berths; N2 — other passengers

Assumptions and limitations

  • The volumes must be measured as the convention requires, to the inside of the shell and including every enclosed space. That measurement is the work of the flag Administration or a recognised organisation; this page only applies the formulas.
  • The draught d is the summer load line draught for cargo ships, the deepest subdivision load line for passenger ships, and 75 % of D for ships with neither.
  • Appendix 2 of the convention tabulates K1 and K2 and allows linear interpolation between its rows. The formula gives the same values at the rows and can differ slightly in the fourth decimal between them.
  • Tonnages are shown to the nearest whole number. The figures on the International Tonnage Certificate are those the Administration determines.

Worked example

A cargo ship has 30 000 m³ of enclosed spaces, of which 16 000 m³ are cargo spaces. Its moulded depth is 12 m and its summer draught 8.5 m. It carries no passengers.

  1. K1 = 0.2 + 0.02 × log10 30 000 = 0.2 + 0.02 × 4.4771 = 0.28954.
  2. GT = 0.28954 × 30 000 = 8 686.
  3. K2 = 0.2 + 0.02 × log10 16 000 = 0.28408.
  4. Draught factor: (4 × 8.5 / (3 × 12))² = (34 / 36)² = 0.8920, below the limit of 1.
  5. Cargo term: 0.28408 × 16 000 × 0.8920 = 4 054, above 0.25 GT = 2 172.
  6. NT = 4 054, above 0.30 GT = 2 606, so no limit applies.

FAQ

Is gross tonnage a weight?

No. It is a dimensionless number derived from volume. A ship's weight is its displacement, and its carrying capacity in tonnes is its deadweight.

What is the difference between gross and net tonnage?

Gross tonnage measures the whole ship. Net tonnage measures the earning spaces: the cargo volume corrected for draught, plus passengers. NT can never be less than 30 % of GT.

How is gross tonnage different from the old gross register tonnage?

Gross register tonnage was a volume in register tons of 100 cubic feet under the older national rules. The 1969 convention, in force since 1982, replaced it with the dimensionless GT.

What is gross tonnage used for?

Many rules and fees depend on it: SOLAS cargo-ship requirements start at 500 GT, and port dues, pilotage and canal fees are often charged per GT or NT.

Why does the draught appear in the net tonnage formula?

A ship that cannot load deep uses less of its cargo volume, so the factor (4d / 3D)² reduces the cargo term when the draught is small compared with the depth.

When do passengers count in net tonnage?

Only when there are 13 or more. Passengers in cabins of up to 8 berths count fully, others one tenth.

Related calculators

What this calculator is checked against

Before every release the calculator must reproduce each case below. The note under each case says where the expected answer comes from: a standard, a textbook, a published table, or a hand calculation shown in full.

  1. Appendix 2 table: K1 = 0.2200 at 10 m³, 0.2600 at 1 000 m³, 0.2800 at 10 000 m³ and 0.3200 at 1 000 000 m³ITC 1969, Annex I, Appendix 2 (coefficients K1 and K2)
  2. Cargo ship: V 30 000 m³ → GT 8 686; Vc 16 000 m³, d 8.5 m, D 12 m → NT 4 054ITC 1969, Annex I, regulations 3 and 4; hand calculation
  3. Passenger ship: V 60 000 m³, no cargo, 1 500 + 200 passengers: cargo term raised to 0.25 GT, K3 = 3.467, NT = 9 703ITC 1969, Annex I, regulation 4(1)(b) and K3 = 1.25 (GT + 10 000)/10 000; hand calculation
  4. Limits: (4d/3D)² capped at 1; fewer than 13 passengers ignored; NT not below 0.30 GTITC 1969, Annex I, regulation 4(1)(a), (c) and the N1 + N2 < 13 rule
  5. A cargo volume above the total and a fractional passenger count are rejectedBehaviour check: warnings and rejected inputs
  6. Worked example of the article: the calculator reproduces 0.28954, 8 686, 0.28408, 0.8920, 4 054 to the digits printedThe worked example on this page, to the digits printed

Assumptions and sources

Assumptions and limits

  • V is the total moulded volume of all enclosed spaces (hull and superstructures) and Vc the volume of the cargo spaces, both in cubic metres and measured as regulation 6 requires. Their measurement is the work of the Administration or a recognised organisation; this page applies the formulas only.
  • K1 and K2 use the formula 0.2 + 0.02 log10 V. Appendix 2 of the convention tabulates the same function and permits linear interpolation between its rows, which can differ from the formula in the fourth decimal.
  • D is the moulded depth amidships (regulation 2(2)) and d the moulded draught of regulation 4(2): the summer load line draught for cargo ships, the deepest subdivision load line for passenger ships, and 75 % of D for ships without either.
  • The limits of regulation 4(1) are applied: (4d/3D)² not more than 1, the cargo term not less than 0.25 GT, NT not less than 0.30 GT, and passengers counted only when there are 13 or more.
  • Results are shown to the nearest whole number; the tonnage certificate states whole numbers as the Administration determines them.

Sources

  • International Convention on Tonnage Measurement of Ships, 1969 (IMO), Annex I, regulation 3 (gross tonnage) and regulation 4 (net tonnage)
  • ITC 1969, Annex I, regulation 2 (moulded depth) and Appendix 2 (coefficients K1 and K2, linear interpolation)
  • UK Merchant Shipping (Tonnage) Regulations 1997 (SI 1997/1510), Part II: the convention formulas as enacted in national law

Cite this calculator

Papandreou, C. (2026). Gross and net tonnage calculator (ITC 1969). Engineering Bible. https://engineeringbible.com/maritime/gross-tonnage/

Embed this calculator on your site

Copy this HTML into your page. The calculator stays free to use and links back here.

By Christos Papandreou. Updated . How the numbers are checked.