Maritime and naval architecture glossary
50 terms from the maritime calculators, each in two or three sentences with its symbol, its unit and a typical value. Every entry links to the calculators that use it; the formula sheet has the equations.
-
Added resistance in wavesRAWkN
Also called wave added resistance, STAwave
The extra resistance a ship meets in a seaway beyond its calm-water resistance, caused mainly by wave reflection at the bow and by heave and pitch motions. It is a few per cent of calm-water power in slight seas and can exceed 20 % in rough head seas. Speed trials and performance analyses remove it before comparing ships.
Added resistance in waves (STAwave-1), Speed–power curve fit, Charter party performance claim
-
Admiralty coefficientCadmt^(2/3)·kn³/kW
An empirical constant linking displacement, speed and power for one hull form: displacement to the power two thirds, times speed cubed, divided by shaft power. It is found from a known operating point and used to estimate power at a nearby speed or draught. It holds only for modest changes, and its value depends on the units chosen.
Admiralty coefficient and speed–power scaling, Speed–power curve fit, Fuel consumption and voyage cost
-
Air draughtm (ft)
Also called air draft, bridge clearance
The vertical distance from the waterline to the highest fixed point of a ship, such as the mast top or radar scanner. It increases as the ship rises in ballast, so it must be worked out for the actual draught and trim and compared with the bridge clearance at the state of tide, less a safety allowance.
Air draft and bridge clearance, Tidal height (rule of twelfths)
-
Anchor holding capacitykN (tonnes-force)
Also called holding power, anchor efficiency
The horizontal pull an embedded anchor resists before it drags, usually stated as its weight times an efficiency. Stockless ship anchors hold about 4 to 6 times their weight in good ground, modern high-holding-power designs about 15 to 50 times. Any upward pull on the shank, from too little cable on the bottom, cuts the holding sharply.
Anchor holding power calculator, Anchor cable catenary and scope
-
Apparent slipdimensionless (%)
Also called propeller slip, slip
The shortfall of a ship's observed speed against the theoretical speed of its propeller, pitch times revolutions, expressed as a fraction of that theoretical speed. Most merchant ships show 5 to 15 % in calm water with a clean hull. It can turn negative with a following current, and a rising trend points to fouling, weather or damage.
Propeller slip and speed through water, Propeller pitch and boat speed calculator
-
Ballast water exchangenone
Also called BWE, D-1 standard
The replacement of ballast water taken on near the coast with open-ocean water, to remove harmful aquatic organisms. Regulation D-1 of the Ballast Water Management Convention requires 95 % volumetric exchange, and pumping three tank volumes through counts as meeting it. Since September 2024 treatment to the D-2 standard is required, with exchange kept as a contingency.
-
Beaufort scalenone
Also called Beaufort wind force
A 0 to 12 scale of wind force, defined by the mean wind speed at 10 m height and the appearance of the sea, as tabulated by the WMO. Force 6 is 22 to 27 knots, force 8 a gale of 34 to 40 knots, and force 12 hurricane force of 64 knots and above.
Beaufort, wind speed and sea state converter, True wind from apparent wind, Charter party performance claim
-
Berthing energyEkJ (kN·m)
Also called fender energy, PIANC berthing
The kinetic energy a fender system must absorb as a ship comes alongside: half the displacement times the approach velocity squared, multiplied by the added-mass, eccentricity, configuration and softness factors of the PIANC method. Large ships approach at only 0.1 to 0.3 m/s, yet a laden tanker can still deliver over 1000 kJ.
-
Block coefficientCBdimensionless
Also called Cb
The ratio of a hull's underwater volume to the box that encloses it, length × beam × draught. Full cargo ships such as tankers and bulk carriers reach 0.80 to 0.85, while fast, fine-lined vessels sit nearer 0.50 to 0.60. It sets how much a hull can carry for its size and strongly affects its resistance.
Block coefficient and hull form coefficients, Hydrostatics basics, Holtrop–Mennen resistance and power, Ship squat and under-keel clearance
-
Bollard pullBPt (kN)
Also called BP, static bollard pull
The static towing force a tug develops at zero speed with its engines at maximum continuous rating, measured by a load cell on a fixed bollard. Harbour tugs commonly certify 50 to 90 t. For a tow, the required pull is the combined wind, current and wave-drift force divided by a tug efficiency of about 0.75.
-
Carbon intensity indicatorCIIg CO₂/(dwt·nmi)
Also called CII, CII rating, AER
The IMO operational measure of a ship's annual CO₂ emissions per unit of transport work, usually grams of CO₂ per deadweight tonne-mile. Ships of 5000 GT and above are rated A to E each year against a required value that tightens annually. A D rating three years running, or one E rating, requires a corrective action plan.
CII rating estimator, Fuel net specific energy and CO₂ factor, EU ETS and FuelEU Maritime
-
Centre of buoyancyB, KBm
Also called KB, LCB
The centroid of a hull's underwater volume, through which the resultant buoyant force acts. Its height above the keel, KB, is exactly half the draught for a box and about 0.52 to 0.58 of the draught for ship forms. It shifts toward the low side as a ship heels, which creates the righting moment.
Hydrostatics basics, Initial stability GM and list, Bilged compartment (lost buoyancy)
-
Closest point of approachCPAnmi
Also called CPA, TCPA, time to closest point of approach
The smallest distance at which another vessel will pass if both keep their present course and speed, found from successive radar plots of its relative motion; TCPA is the time until that point. Many masters set a minimum CPA of 1 to 2 nautical miles in open water and less in confined waters.
-
Compass error° (E or W)
Also called deviation, variation, gyro error
The angle between the north shown by a compass and true north, named east or west; for a magnetic compass it is the sum of variation, from the Earth's field, and deviation, from the ship's own magnetism. It is checked by comparing the compass bearing of the sun or a star with its calculated true bearing by amplitude or azimuth.
Compass error by amplitude or azimuth, Sight reduction (intercept method)
-
DeadweightDWTt
Also called DWT, deadweight tonnage
The mass a ship can carry: the difference between its displacement at a given draught and its lightship mass, covering cargo, fuel, ballast, fresh water, stores, crew and constants. Quoted at the summer load line, it is the commercial size measure of tankers and bulk carriers, around 180 000 t for a Capesize bulk carrier.
Loading condition from an item list, Draft survey, Hydrostatics basics, CII rating estimator
-
DisplacementΔt
Also called displacement tonnage, volume of displacement
The mass of water a floating ship displaces, equal to its own total mass: underwater volume times water density, 1.025 t/m³ in sea water. Quoted at a stated draught, it is the starting figure for stability, trim, resistance and berthing energy calculations; the underwater volume itself is the volume of displacement, ∇.
Hydrostatics basics, Block coefficient and hull form coefficients, Buoyancy calculator (Archimedes), Draft survey, Loading condition from an item list
-
Draught surveynone
Also called draft survey, quarter-mean draught
A method of finding the mass of cargo loaded or discharged from the ship's draughts, read at six marks before and after, corrected for trim, hog or sag and water density, with ballast, fuel and fresh water deducted. A careful survey is accurate to about 0.5 % of the cargo, so it is the standard for bulk cargoes.
-
Effective powerPEkW
Also called towing power, EHP
The power needed to tow a hull at a given speed, total resistance times speed, before any propeller or shaft losses. Dividing it by the propulsive efficiency, typically 0.6 to 0.75 for merchant ships, gives the power delivered to the propeller. Resistance predictions and trial corrections are expressed through it.
Holtrop–Mennen resistance and power, Hull roughness and fouling penalty, Water temperature and density correction, Wind resistance (ISO 15016)
-
Emission control areaECAnone
Also called ECA, SECA, NECA
A sea area designated under MARPOL Annex VI where stricter emission limits apply: fuel sulphur of at most 0.10 % by mass, and in NOx areas Tier III engine limits for ships built from the date set for that area. Ships change over fuel before entry so that compliant oil reaches the engines by the boundary.
Fuel changeover before an ECA, NOx tier limit by engine speed
-
Encounter periodTEs
Also called period of encounter, encounter frequency
The time between successive wave crests as met by a moving ship, which differs from the wave period because of the ship's speed and heading. It is shorter than the wave period in head seas and longer in following seas. When it is near the natural roll period, or half of it, synchronous or parametric rolling can build up.
Wave properties and encounter period, Roll period and synchronous rolling
-
Free surface effectFSCm
Also called free surface correction, FSM
The virtual rise in a ship's centre of gravity, and so loss of metacentric height, caused by liquid shifting to the low side in a slack tank. The loss equals the tank's free surface moment of inertia times the liquid density, divided by displacement. It grows with tank breadth cubed and hardly depends on how much liquid is in the tank.
Initial stability GM and list, Loading condition from an item list, Inclining experiment
-
Freeboardmm (m)
Also called load line, Plimsoll mark
The vertical distance at the side amidships from the waterline to the upper edge of the freeboard deck line. The Load Line Convention assigns a minimum summer freeboard from length, block coefficient, depth and superstructures, with tropical, winter and fresh-water marks set around it. It preserves reserve buoyancy and keeps the deck clear of green water.
-
Fresh water allowanceFWAmm
Also called FWA, dock water allowance, DWA
The increase in a ship's mean draught when it passes from sea water of 1.025 t/m³ into fresh water at the same displacement, equal to displacement divided by four times TPC, in millimetres. It lets a ship load in a river port beyond its seasonal mark and rise to it at sea; the dock water allowance applies the same idea to brackish water.
-
Froude numberFndimensionless
Also called Fn, length Froude number, depth Froude number
The ratio of a ship's speed to the speed of a gravity wave as long as the hull, V / √(g L) with L the waterline length, which governs wave-making. Large cargo ships run at 0.15 to 0.25 and displacement boats reach their hull speed near 0.40. The depth Froude number, V / √(g h), approaching 1 marks the critical speed in shallow water.
Froude number calculator for ships and boats, Hull speed calculator, Holtrop–Mennen resistance and power, Ship squat and under-keel clearance, Wave properties and encounter period
-
FuelEU Maritimeg CO₂e/MJ
Also called FuelEU, GHG intensity
The EU regulation, applying from 2025 to ships of 5000 GT and above, that limits the yearly average well-to-wake greenhouse gas intensity of the energy used on board. The limit is 2 % below the reference of 91.16 g CO₂e/MJ from 2025, tightening to 6 % in 2030 and 80 % in 2050, with a penalty of 2400 EUR per tonne of VLSFO-equivalent shortfall.
EU ETS and FuelEU Maritime, Fuel net specific energy and CO₂ factor, Alternative fuel tank volume
-
Great circlenmi
Also called great-circle sailing, orthodrome
The intersection of the Earth's surface with a plane through its centre, giving the shortest route between two points on a sphere. Its course changes continuously, so it is sailed as a series of rhumb-line legs. The saving over the rhumb line is greatest on long east-west passages in high latitudes, often hundreds of miles on an ocean crossing.
Great-circle and rhumb-line distance, Passage plan from waypoints, Mercator (rhumb-line) sailing
-
Gross tonnageGTdimensionless
Also called GT, net tonnage, NT
A measure of a ship's overall size under the 1969 Tonnage Convention, GT = K1 × V, where V is the volume of all enclosed spaces in m³ and K1 = 0.2 + 0.02 log₁₀ V. It is a number, not a mass, and sets port dues, manning and the regulations that apply; net tonnage, at least 30 % of GT, reflects the cargo spaces.
Gross and net tonnage calculator (ITC 1969), EU ETS and FuelEU Maritime, CII rating estimator
-
Hull foulingnone
Also called biofouling, hull roughness
The growth of slime, weed and shell organisms on a ship's underwater hull, which roughens it and raises frictional resistance. Light slime adds a few per cent to the power needed, heavy calcareous fouling 30 % or more. Cleaning and coating intervals are chosen to balance this fuel penalty against the cost of each cleaning.
Hull roughness and fouling penalty, Optimal hull cleaning interval, Speed–power curve fit, Propeller curve and light running margin
-
Hull speedkn
Also called speed-length ratio, displacement speed
The speed at which a displacement hull's bow wave grows as long as its waterline, traditionally 1.34 × √(waterline length in feet) knots, or about 2.43 × √(length in metres). Beyond it wave-making resistance rises steeply, so heavy displacement boats barely exceed it, while light, slender or planing hulls can.
Hull speed calculator, Froude number calculator for ships and boats, Planing boat speed calculator (Crouch formula)
-
Inclining experimentnone
Also called inclining test, lightweight survey
A test in which known weights are moved across the deck of a nearly complete ship and the small resulting heel is measured with pendulums or inclinometers, to find the metacentric height and so the lightship centre of gravity. GM equals weight moved times distance, divided by displacement times the tangent of the heel angle.
-
Light running marginLRMdimensionless (%)
Also called LRM, propeller light running
The rpm allowance by which an engine is laid out on a propeller curve lighter than the clean-hull design curve, so that later fouling, weather and deeper draught do not push it into its torque limit. Engine designers recommend 4 to 7 % for most ships and up to 10 % in special cases.
Propeller curve and light running margin, Speed–power curve fit
-
Longitudinal centre of flotationLCFm
Also called LCF, centre of flotation, tipping centre
The centroid of the waterplane area, the point about which a ship trims when weights are shifted or small weights loaded. A weight placed directly above it produces bodily sinkage without change of trim. It lies near midships and is read from the hydrostatic tables, measured from midships or the aft perpendicular.
Change of trim and new drafts calculator, Hydrostatics basics, Draft survey
-
Metacentric heightGMm
Also called GM, KM, metacentre
The vertical distance between a ship's centre of gravity G and its transverse metacentre M, measuring its initial resistance to heeling: GM = KB + BM − KG. The IS Code requires at least 0.15 m and cargo ships commonly carry 0.5 to 3 m. Too little GM makes a tender ship, too much a stiff, violent roll.
Initial stability GM and list, GZ curve and intact stability criteria, Inclining experiment, Roll period and synchronous rolling, Loading condition from an item list, Bilged compartment (lost buoyancy)
-
Moment to change trim one centimetreMCTCt·m/cm
Also called MCTC, MCT 1 cm
The trimming moment that alters a ship's trim, the difference between aft and forward draughts, by 1 cm, approximately displacement times longitudinal metacentric height divided by 100 times the length between perpendiculars. Change of trim in centimetres equals the trimming moment about the centre of flotation divided by this value, read from the hydrostatic tables.
Change of trim and new drafts calculator, Hydrostatics basics, Draft survey, Loading condition from an item list
-
Natural roll periodT_φs
Also called rolling period, roll period
The time for one full roll cycle, from one side to the other and back, of a ship heeled and released in calm water. The IS Code estimate is 2 C B / √GM with C typically 0.35 to 0.40, close to the shipboard rule 0.8 B / √GM. A short period marks a stiff ship, and timing the roll at sea gives a quick check of GM.
Roll period and synchronous rolling, Initial stability GM and list, GZ curve and intact stability criteria
-
NOx tier limitsg/kWh
Also called Tier III, Tier II, NOx Technical Code
The MARPOL Annex VI Regulation 13 limits on nitrogen oxide emissions from marine diesel engines above 130 kW, set by rated engine speed and construction date. Below 130 rpm, Tier I allows 17.0 g/kWh and Tier II 14.4 g/kWh; Tier III, required inside NOx emission control areas, cuts this to 3.4 g/kWh.
-
Prismatic coefficientCPdimensionless
Also called longitudinal prismatic coefficient, Cp
The ratio of a hull's underwater volume to a prism with the midship section area and the waterline length, equal to C_B / C_M. It describes how volume is spread toward the ends: about 0.55 to 0.65 suits faster ships and 0.75 to 0.85 full cargo ships. It has a strong influence on wave-making resistance.
Block coefficient and hull form coefficients, Holtrop–Mennen resistance and power
-
Propeller pitchPm (in)
Also called pitch ratio, P/D
The distance a propeller would advance in one revolution if it moved through a solid like a screw, usually quoted at 0.7 of the propeller radius. Pitch ratios P/D of merchant propellers are commonly 0.6 to 1.2. Pitch times rpm gives the theoretical speed, and slip measures the shortfall of the actual speed.
Propeller pitch and boat speed calculator, Propeller slip and speed through water, Wageningen B-series propeller
-
Rhumb linenmi
Also called loxodrome, Mercator sailing
A line crossing every meridian at the same angle, so it is sailed on a constant course and appears straight on a Mercator chart. It is longer than the great circle except along a meridian or the equator, the difference growing with distance and latitude; course and distance are worked from meridional parts.
Mercator (rhumb-line) sailing, Great-circle and rhumb-line distance, Passage plan from waypoints
-
Righting leverGZm
Also called GZ, GZ curve, righting arm
The horizontal distance between the centre of gravity and the line of action of buoyancy when a ship is heeled; times displacement it gives the righting moment. Plotted against heel it forms the GZ curve, and the IS Code requires at least 0.20 m at 30° or more, with the maximum at 25° or beyond.
GZ curve and intact stability criteria, Initial stability GM and list, Loading condition from an item list
-
Safe working loadSWLt (kN)
Also called SWL, WLL, working load limit
The maximum load a lifting, mooring or securing item is certified to carry in service, its minimum breaking load divided by a safety factor. Steel wire rope slings commonly use a factor of 5. The CSS Code instead gives cargo lashings a maximum securing load as a set fraction of their breaking strength.
Wire rope and chain safe working load calculator, Cargo securing (CSS Code Annex 13), Mooring line and winch brake (MEG4)
-
Sea margindimensionless (%)
Also called service margin
The power allowance added to the calm-water, clean-hull power for the service speed, to cover wind, waves and fouling in service. It is traditionally 15 % when selecting the main engine, and 20 to 30 % for ships on rough routes such as the North Atlantic.
Propeller curve and light running margin, Holtrop–Mennen resistance and power, Speed–power curve fit
-
Ship squatm
Also called squat, Barrass squat
The bodily sinkage and trim of a ship moving in shallow water, caused by faster flow and lower pressure beneath the hull. Barrass's rule gives maximum squat in metres as about C_B × V² / 100 in open water, V in knots, and twice that in a confined channel. It eats into under-keel clearance just where the depth is least.
Ship squat and under-keel clearance, Froude number calculator for ships and boats, Shallow water correction (Raven / Lackenby)
-
Significant wave heightHsm
Also called Hs, H1/3
The mean height of the highest third of the waves in a sea state, or 4 √m₀ from the wave spectrum, close to the height an experienced observer estimates by eye. The highest single wave in a three-hour storm is typically 1.6 to 2 times H_s, which is why design uses the expected maximum, not H_s.
Sea state statistics, Wave properties and encounter period, Added resistance in waves (STAwave-1), Beaufort, wind speed and sea state converter
-
Specific fuel oil consumptionSFOCg/kWh
Also called SFOC, specific fuel consumption
The mass of fuel a marine diesel engine burns per unit of work delivered at a stated load, quoted for a reference fuel of 42.7 MJ/kg lower calorific value. Large two-stroke engines achieve about 155 to 175 g/kWh and medium-speed four-strokes about 170 to 195 g/kWh. Values must be corrected to the actual fuel before comparison.
Fuel consumption and voyage cost, Boat fuel consumption calculator, Charter party performance claim, Fuel net specific energy and CO₂ factor, Admiralty coefficient and speed–power scaling
-
Tonnes per centimetre immersionTPCt/cm
Also called TPC, TPI
The mass that must be loaded or discharged to change a ship's mean draught by 1 cm, waterplane area times water density divided by 100. A Panamax bulk carrier has about 65 t/cm at its loaded draught. It converts small loads into parallel sinkage and is read from the hydrostatic tables at the current draught.
Hydrostatics basics, Change of trim and new drafts calculator, Draft survey
-
Trimm (cm)
Also called trim by the stern, trim by the head
The difference between a ship's aft and forward draughts; a ship deeper aft is trimmed by the stern. A change of trim from moving or loading a weight equals the trimming moment about the centre of flotation divided by MCTC. Moderate stern trim usually helps steering and propeller immersion, while excess trim raises resistance.
Change of trim and new drafts calculator, Hydrostatics basics, Draft survey, Tank sounding trim and heel correction, Dry-docking critical instant
-
Under-keel clearanceUKCm
Also called UKC, net under-keel clearance
The vertical distance between the lowest point of a ship's keel and the seabed, after allowing for tide, squat, wave motion and heel. Ports and pilotage authorities commonly require a net clearance of at least 10 % of the static draught in sheltered channels and more in exposed approaches.
Ship squat and under-keel clearance, Tidal height (rule of twelfths), Shallow water correction (Raven / Lackenby)
-
Wake fractionwdimensionless
Also called Taylor wake fraction, speed of advance
The fractional reduction in the speed of the water reaching the propeller compared with the ship's speed, because the hull drags water along with it: speed of advance V_A = V (1 − w). Single-screw ships typically have Taylor wake fractions of 0.20 to 0.35, twin-screw ships 0.10 to 0.20.
Holtrop–Mennen resistance and power, Propeller slip and speed through water, Wageningen B-series propeller
-
Wave-making resistanceRWkN
Also called wave resistance
The part of a ship's resistance spent generating the wave system that trails from the hull, rising steeply with Froude number. It is a minor share of the total for full cargo ships below Fn 0.2 but dominates near Fn 0.4 to 0.5, which is why displacement hulls meet a practical speed limit.
Holtrop–Mennen resistance and power, Froude number calculator for ships and boats, Hull speed calculator
Results are estimates. They do not replace the governing code, class or flag requirements, or a check by a competent person.