Skip to content
Engineering Bible

Results appear as you type. Use the arrow keys to move through them and Enter to open one.

Popular

↑ ↓ moveEnter openEsc close

Chemical dosing calculator (feed rate, pump setting, chlorine dose)

Chemical feed rate and dosing pump setting in L/h and gal/day from flow, dose in mg/L, product strength and density, with chlorine dose, demand and residual.

Units

Results are estimates. They do not replace the governing code, class or flag requirements, or a check by a competent person. Report a problem

Introduction

How much chemical does a water treatment dose need? Multiply the water flow by the dose to get the active chemical, then divide by the product strength to get the product. A dose of 1 mg/L puts 1 g of chemical into every cubic metre, or 8.34 lb into every million US gallons. Dosing 100 m³/h at 5 mg/L takes 0.5 kg/h of active chemical. With trade-strength sodium hypochlorite at 12.5 % that is 4 L/h of product.

This calculator gives the active chemical feed, the product feed by mass and volume, the dosing pump setting in L/h, mL/min and US gal/day, and the daily product use. It accepts product strength as % w/w or as % w/v. It also solves the chlorine relation dose = demand + residual for any one term. It is for water and wastewater operators, process engineers and students sizing dosing pumps and chemical storage.

Formulas

Active chemical and product feed:

active [g/h] = Q [m³/h] × dose [mg/L]
product mass = active / w
product volume = product mass / ρ_product = active / c

US pounds formula:

lb/day = flow [MGD] × dose [mg/L] × 8.34

Chlorine:

dose = demand + residual
  • Q — water flow; dose — active chemical per litre of water, mg/L = g/m³
  • w — product strength as a mass fraction (% w/w / 100)
  • c — product strength as mass per volume: % w/v × 10 = g/L, and % w/v = % w/w × SG
  • ρ_product — product density; SG — its specific gravity
  • 8.34 — pounds per US gallon of water, which turns MGD × mg/L into lb/day

Assumptions and limitations

  • The dose applies to the whole flow and mixes completely. Dose rates for disinfection, coagulation or pH control come from jar tests, regulations or the supplier.
  • Trade-strength hypochlorite is sold by available chlorine in % w/v. At SG 1.2, 12.5 % w/v is 10.4 % w/w. Choose the basis that matches the product data sheet.
  • The pump setting is the product rate while water flows. Pump ratings in gal/day are the same rate over 24 hours.
  • Hypochlorite loses strength in storage, faster when warm or exposed to light. Check the strength and adjust the pump.
  • Chlorine demand varies with water quality and contact time. Measure the residual and adjust the dose to hold it.

Worked example

A plant treats 100 m³/h of water and wants a chlorine dose of 5 mg/L. It uses sodium hypochlorite with 12.5 % w/v available chlorine and a density of 1 200 kg/m³. What pump setting is needed?

  1. Active chlorine: 100 m³/h × 5 g/m³ = 500 g/h, or 12.0 kg per day.
  2. Product strength: 12.5 % w/v = 125 g/L of product.
  3. Pump setting: 500 / 125 = 4.00 L/h, which is 4.00 × 24 / 3.785 = 25.4 US gal/day.
  4. Product used: 4.00 L/h × 24 h = 96 L a day, or 96 × 1.2 = 115.2 kg.

A 1 000 L tank of product lasts about 10 days at this rate.

FAQ

How do I calculate a chemical dosing rate?

Multiply the flow by the dose, then divide by the product strength. For 50 m³/h at 10 mg/L with a 40 % w/w product of density 1 400 kg/m³, the feed is 0.5 kg/h of active, 1.25 kg/h of product, or 0.89 L/h.

What is the pounds formula?

Pounds per day equals flow in million gallons per day times dose in mg/L times 8.34. A 2.5 MGD plant dosing 3 mg/L uses 62.6 lb of chlorine a day.

What is the difference between chlorine dose, demand and residual?

The dose is what you add. The demand is what reacts with the water's impurities. The residual is what is left, and it keeps disinfecting in the network.

What chlorine residual should drinking water have?

Many utilities aim for at least 0.2 mg/L of free chlorine at the far end of the network. The US EPA caps the residual at 4.0 mg/L.

What does 12.5 % sodium hypochlorite mean?

12.5 g of available chlorine per 100 mL, which is 125 g/L. At SG 1.2 it is about 10.4 % by weight.

How do I convert L/h to gallons per day?

Multiply by 24 and divide by 3.785. A pump delivering 1 L/h moves 6.34 US gal/day.

Related calculators

What this calculator is checked against

Before every release the calculator must reproduce each case below. The note under each case says where the expected answer comes from: a standard, a textbook, a published table, or a hand calculation shown in full.

  1. 100 m³/h at 5 mg/L with 12.5 % w/v hypochlorite (1 200 kg/m³): 12.0 kg/day active, 4.00 L/h, 25.36 US gal/day, 115.2 kg/dayHand calculation: active = Q × dose; product volume = active / (125 g/L)
  2. Pounds formula: 1 MGD at 1 mg/L needs 8.34 lb/day; 2.5 MGD at 3 mg/L needs 62.6 lb/day of chlorineCSU Sacramento, Water Treatment Plant Operation Vol. I: lb/day = MGD × mg/L × 8.34
  3. Chlorine: demand 1.5 + residual 0.5 = dose 2.0 mg/L; a 3.0 mg/L dose with 0.6 mg/L residual has 2.4 mg/L demandChlorine dose = demand + residual (CSU Sacramento; Metcalf & Eddy ch. 12)
  4. Calcium hypochlorite at 65 % w/w: 100 lb of chlorine needs 153.8 lb of product; the % w/w and % w/v routes agreeCSU Sacramento: lb of hypochlorite = lb of chlorine / (% available chlorine / 100); consistency of the two bases
  5. Fewer dosing hours scale the daily use but not the pump rate; 1 L/h is 6.34 US gal/dayHand calculation (24 h / 3.785 L per gal)
  6. A residual above the dose, zero flow and an impossible strength are rejected; a high residual warnsBehaviour check: warnings and rejected inputs
  7. Worked example of the article: the calculator reproduces 12.0 kg, 4.00, 25.4, 115.2 kg to the digits printedThe worked example on this page, to the digits printed

Assumptions and sources

Assumptions and limits

  • The dose is the mass of active chemical per litre of treated water (mg/L = g/m³), applied to the whole flow; 1 mg/L in 1 m³ is 1 g, and in 1 million US gallons 8.34 lb.
  • Product strength is the active content of the delivered product: % w/w is per mass of product, % w/v is grams per 100 mL (as for trade-strength hypochlorite, where % w/v = % w/w × specific gravity).
  • The pump setting is the product volume per hour while the water flows; the daily use is that rate times the dosing hours per day. Pump ratings in gal/day are the same rate over 24 hours.
  • Chlorine dose equals chlorine demand plus the residual left after the contact time; the demand depends on the water and the contact time, so measure the residual and adjust.
  • Sodium hypochlorite loses strength in storage, faster when warm; check the strength of the product on delivery and periodically.

Sources

  • Office of Water Programs, California State University, Sacramento: Water Treatment Plant Operation, Vol. I, chapter on disinfection (chlorine dose = demand + residual; pounds formula lb/day = MGD × mg/L × 8.34)
  • AWWA B300, Standard for Hypochlorites (sodium and calcium hypochlorite supplied for water treatment)
  • Metcalf & Eddy, Wastewater Engineering: Treatment and Resource Recovery, 5th ed., ch. 12 (chlorine dose, demand and residual)

Cite this calculator

Papandreou, C. (2026). Chemical dosing calculator (feed rate, pump setting, chlorine dose). Engineering Bible. https://engineeringbible.com/process/chemical-dosing/

Embed this calculator on your site

Copy this HTML into your page. The calculator stays free to use and links back here.

By Christos Papandreou. Updated . How the numbers are checked.