Skip to content
Engineering Bible

Results appear as you type. Use the arrow keys to move through them and Enter to open one.

Popular

↑ ↓ moveEnter openEsc close

Load combinations calculator (ASCE 7 LRFD/ASD and Eurocode)

Factored load combinations from dead, live, roof, snow, rain, wind and seismic loads by ASCE 7-16 LRFD or ASD, or EN 1990 6.10, with the governing case.

Units

Results are estimates. They do not replace the governing code, class or flag requirements, or a check by a competent person. Report a problem

Introduction

A structure must be designed for loads acting together, not one at a time. Codes set out load combinations: sums of the dead, live, snow, wind and seismic loads, each with its own factor. The largest result governs the design, and the smallest shows any uplift. A beam with a dead load of 10 kN, live 8, roof live 2, snow 5 and wind 6 needs 28.5 kN by ASCE 7-16 LRFD, from 1.2D + W + L + 0.5S.

This calculator evaluates every combination of ASCE 7-16 for strength design (LRFD) or allowable stress design (ASD), or of EN 1990 with expression 6.10 or 6.10a and 6.10b. It expands the "or" choices, takes wind and seismic in both directions, and reports the governing maximum and minimum. It is for structural engineers, students and anyone checking a reaction, moment or force under code combinations.

Formulas

ASCE 7-16 LRFD (section 2.3.1):

1. 1.4D
2. 1.2D + 1.6L + 0.5(Lr or S or R)
3. 1.2D + 1.6(Lr or S or R) + (L or 0.5W)
4. 1.2D + 1.0W + L + 0.5(Lr or S or R)
5. 1.2D + 1.0E + L + 0.2S
6. 0.9D + 1.0W
7. 0.9D + 1.0E

ASCE 7-16 ASD (section 2.4.1):

D;  D + L;  D + (Lr or S or R);  D + 0.75L + 0.75(Lr or S or R)
D + (0.6W or 0.7E);  D + 0.75L + 0.75(0.6W) + 0.75(Lr or S or R)
D + 0.75L + 0.75(0.7E) + 0.75S;  0.6D + 0.6W;  0.6D + 0.7E

EN 1990 (STR, persistent and transient):

6.10:   1.35 G + 1.5 Q_1 + Σ 1.5 ψ0,i Q_i
6.10a:  1.35 G + Σ 1.5 ψ0,i Q_i
6.10b:  0.85 × 1.35 G + 1.5 Q_1 + Σ 1.5 ψ0,i Q_i
6.12b:  G + A_Ed + Σ ψ2,i Q_i   (seismic)
  • D or G — dead load; L — live load; Lr — roof live load; S — snow; R — rain; W — wind; E — earthquake
  • ψ0: 0.7 for categories A to D, F and G, 1.0 for storage, 0.5 or 0.7 for snow, 0.6 for wind, 0 for roofs
  • Favourable dead load takes γ = 1.0, and favourable variable loads are left out

Assumptions and limitations

  • Every load is the same kind of effect, such as a reaction or a moment, in one unit. Gravity is positive.
  • Wind and seismic effects are taken in both directions. A negative minimum means uplift or a reversal of force.
  • ASCE 7 allows 0.5 on L in combinations 3 to 5 where the live load is 100 psf or less, except garages and assembly areas. E is the seismic load effect of section 12.4.
  • The Eurocode values are the recommended ones. National annexes can change them. Roof imposed loads are not combined with snow or wind, and rain is not a separate action.

Worked example

A beam reaction has these unfactored parts: D = 10, L = 8, Lr = 2, S = 5 and W = 6 kN, with no rain or seismic load. Find the governing LRFD combinations.

  1. Combination 1: 1.4 × 10 = 14.0 kN.
  2. Combination 2 with snow: 1.2 × 10 + 1.6 × 8 + 0.5 × 5 = 27.3 kN.
  3. Combination 3 with snow and L: 12 + 1.6 × 5 + 8 = 28.0 kN.
  4. Combination 4 with wind downward and snow: 12 + 6 + 8 + 0.5 × 5 = 28.5 kN. This is the largest.
  5. Combination 6 with wind upward: 0.9 × 10 − 6 = 3.0 kN. This is the smallest, so there is no uplift.

By ASD the same reaction is 22.45 kN, and by EN 1990 expression 6.10 it is 34.8 kN with snow leading.

FAQ

What is the difference between LRFD and ASD combinations?

LRFD factors the loads up and compares them with a reduced strength. ASD uses smaller factors, often 1.0, and compares with an allowable stress. Each needs its own design values.

Why is 0.9D used in some combinations?

Dead load resists uplift and overturning. Taking only 90 % of it is conservative where it helps.

What does "Lr or S or R" mean?

Use whichever of the three gives the worst effect. The page evaluates all three and keeps the governing one.

Which Eurocode expression should I use, 6.10 or 6.10a/b?

The national annex decides. The larger of 6.10a and 6.10b never exceeds 6.10, so the pair is more economical where it is allowed.

What are ψ factors?

Combination factors that reduce accompanying variable loads, because they rarely reach their full values at the same time as the leading load.

Do I need to consider wind in both directions?

Yes. Wind on a roof can press down or lift up, and lateral wind or seismic loads can come from either side.

Related calculators

What this calculator is checked against

Before every release the calculator must reproduce each case below. The note under each case says where the expected answer comes from: a standard, a textbook, a published table, or a hand calculation shown in full.

  1. ASCE 7-16 LRFD with D 10, L 8, Lr 2, S 5, W 6: 1.4D = 14; 2(S) = 27.3; 3(S, L) = 28; 4(+W, S) = 28.5 governs; 6(−W) = 0.9 × 10 − 6 = 3.0 is the minimumASCE/SEI 7-16, 2.3.1 combinations 1 to 7; hand calculation
  2. ASCE 7-16 LRFD exception: with 0.5 on L, combination 4 drops to 24.5; seismic E 7 gives 1.2D + E + L + 0.2S = 28 and 0.9D − E = 2ASCE/SEI 7-16, 2.3.1 Exception 1 and combinations 5 and 7
  3. ASCE 7-16 ASD: D + L = 18; D + 0.75L + 0.75(0.6W) + 0.75S = 22.45 governs; 0.6D − 0.6W = 2.4 is the minimum; 0.6D + 0.7E with E 10 is 13ASCE/SEI 7-16, 2.4.1 combinations 1 to 8; hand calculation
  4. EN 1990 6.10, category A, snow below 1 000 m: snow leading 1.35 × 10 + 1.5 × 5 + 1.5 × 0.7 × 8 + 1.5 × 0.6 × 6 = 34.8; roof load leading excludes snow and wind (24.9); uplift 1.0 × 10 − 1.5 × 6 = 1.0EN 1990 6.10 with Table A1.1 ψ0 (A 0.7, snow 0.5, wind 0.6, H 0) and Table A1.2(B) γ factors; A1.2.1(3)
  5. EN 1990 6.10a/b: 6.10a = 1.35 × 10 + 1.5(0.7 × 8 + 0.5 × 5 + 0.6 × 6) = 31.05; 6.10b snow leading 0.85 × 1.35 × 10 + 7.5 + 8.4 + 5.4 = 32.775 governs; seismic 6.12b G + E + 0.3 L = 22.4 for E 10; rain is ignored and bad input refusedEN 1990 expressions 6.10a, 6.10b (ξ = 0.85) and 6.12b with ψ2 = 0.3 for category A
  6. Worked example of the article: the calculator reproduces 28.5, 3.0 to the digits printedThe worked example on this page, to the digits printed

Assumptions and sources

Assumptions and limits

  • Each load is the effect of one load case on the same quantity (a reaction, a moment, an axial force) in one consistent unit, positive in the direction of gravity.
  • Wind and earthquake effects act in either direction, so every combination with W or E is evaluated with both signs; the minimum shows uplift or reversal.
  • ASCE 7-16: the load factor on L in combinations 3, 4 and 5 may be 0.5 where the live load is 100 psf or less, except in garages and places of public assembly (2.3.1 Exception 1). E is the combined seismic load effect of 12.4; the special combinations of 2.3.6 with E_v are not split out.
  • EN 1990: expressions 6.10 or 6.10a and 6.10b for persistent and transient STR design with the recommended γ_G = 1.35 (1.00 when favourable), γ_Q = 1.5 and ψ factors of Table A1.1; variable actions enter only where unfavourable, and roof imposed loads are not combined with snow or wind (A1.2.1(3)). National annexes can change the values. Rain R has no EN 1990 counterpart and is ignored there.
  • The seismic combination of EN 1990 6.12b takes E as the design seismic action A_Ed with ψ2 on the imposed and snow loads.

Sources

  • ASCE/SEI 7-16 Minimum Design Loads and Associated Criteria for Buildings and Other Structures, 2.3.1 (LRFD basic combinations), 2.3.6 and 2.4.1 (ASD basic combinations)
  • EN 1990:2002+A1:2005 Eurocode — Basis of structural design, 6.4.3.2 expressions 6.10, 6.10a, 6.10b; 6.4.3.4 expression 6.12b; Annex A1, Table A1.1 (ψ factors) and Table A1.2(B) (γ factors)
  • International Building Code 2021, section 1605 Load Combinations (adopting the ASCE 7 combinations)

Cite this calculator

Papandreou, C. (2026). Load combinations calculator (ASCE 7 LRFD/ASD and Eurocode). Engineering Bible. https://engineeringbible.com/structural/load-combinations/

Embed this calculator on your site

Copy this HTML into your page. The calculator stays free to use and links back here.

By Christos Papandreou. Updated . How the numbers are checked.