Skip to content
Engineering Bible

Results appear as you type. Use the arrow keys to move through them and Enter to open one.

Popular

↑ ↓ moveEnter openEsc close

Elastic constants calculator (E, G, K, Poisson's ratio)

Young's modulus, shear modulus, bulk modulus and Poisson's ratio of an isotropic material from any two of them, with Lamé's constant.

Units

Results are estimates. They do not replace the governing code, class or flag requirements, or a check by a competent person. Report a problem

Introduction

An isotropic elastic material has only two independent elastic constants. Once you know any two of Young's modulus E, the shear modulus G, the bulk modulus K and Poisson's ratio ν, the others follow. Steel with E = 210 GPa and ν = 0.3 has G = 80.8 GPa and K = 175 GPa.

This calculator takes any pair and returns all four constants, plus Lamé's first parameter λ and the constrained modulus M used in wave and soil problems. It refuses pairs that no stable material can have. It is for engineers and students who have E and ν from a data sheet but need G for torsion or K for pressure.

Formulas

From E and ν:

G = E / (2 (1 + ν))
K = E / (3 (1 − 2ν))
λ = E ν / ((1 + ν)(1 − 2ν)),    M = K + 4G/3

From the other pairs:

E and G:  ν = E / (2G) − 1
E and K:  ν = (3K − E) / (6K)
G and K:  E = 9KG / (3K + G),   ν = (3K − 2G) / (2 (3K + G))
G and ν:  E = 2G (1 + ν)
K and ν:  E = 3K (1 − 2ν)
  • E — Young's modulus, tension or compression; G — shear modulus (modulus of rigidity)
  • K — bulk modulus, pressure over volume strain; ν — Poisson's ratio, lateral over axial strain

Typical values from standards and data sheets:

MaterialE (GPa)G (GPa)νSource
Structural steel210810.3EN 1993-1-1
Aluminium alloys70270.3EN 1999-1-1
Stainless steel 30419378—Cleveland-Cliffs
Copper C1100011744.1—National Bronze
Brass C2600011041.4—National Bronze
Ti-6Al-4V113.8440.342ASM data sheet
Float glass70—0.2AGC Planibel
Concrete C30/3733—0.2EN 1992-1-1

Assumptions and limitations

  • The relations hold only for isotropic, linear-elastic materials. Timber, fibre composites and many moulded plastics have different stiffness in different directions.
  • Poisson's ratio must lie between −1 and 0.5. At 0.5 the material cannot change volume and K is infinite, so the calculator stops just below it.
  • Published E, G and ν for an alloy often disagree slightly, because each comes from a different test. EN 1999-1-1 lists 70, 27 and 0.3 for aluminium, but 70 and 27 imply ν = 0.296.
  • For rubber and other nearly incompressible materials, K is very sensitive to the third decimal of ν. Measure K directly instead.

Worked example

A steel shaft has E = 210 GPa and ν = 0.3. What are its shear and bulk moduli?

  1. Shear modulus: G = 210 / (2 × 1.3) = 80.77 GPa.
  2. Bulk modulus: K = 210 / (3 × 0.4) = 175.0 GPa.
  3. Lamé's parameter: λ = 210 × 0.3 / (1.3 × 0.4) = 121.2 GPa.
  4. Constrained modulus: M = 175.0 + 4 × 80.77 / 3 = 282.7 GPa.

Eurocode 3 rounds the shear modulus of steel to 81 GPa, within 0.3 % of this result.

FAQ

What is the relation between E and G?

G = E / (2 (1 + ν)). For metals with ν near 0.3, the shear modulus is about 38 % of Young's modulus.

What is a typical Poisson's ratio?

About 0.3 for steel and aluminium, 0.2 for glass and concrete, and close to 0.5 for rubber.

Can Poisson's ratio be negative?

Yes, for some foams and lattice structures that get fatter when stretched. No common engineering metal does this.

What is the bulk modulus used for?

It relates a pressure to the change in volume. Hydraulic and pressure-vessel calculations use it, and so does the speed of sound in solids.

Why does my data sheet's G not match E and ν?

The three values come from separate tests and products, and each is rounded. A difference of a few per cent is normal.

What is the shear modulus of steel?

Eurocode 3 uses 81 GPa for structural steel. The Cleveland-Cliffs data sheets give 77 to 78 GPa for stainless steels 316 and 304.

Related calculators

What this calculator is checked against

Before every release the calculator must reproduce each case below. The note under each case says where the expected answer comes from: a standard, a textbook, a published table, or a hand calculation shown in full.

  1. Steel E 210 GPa, ν 0.3: G = 210/2.6 = 80.77 GPa, K = 210/1.2 = 175 GPa, λ = 121.15 GPa, M = 282.69 GPaG = E/(2(1 + ν)), K = E/(3(1 − 2ν)), λ = Eν/((1 + ν)(1 − 2ν)) (Timoshenko and Goodier); EN 1993-1-1 §3.2.6 rounds G to 81 GPa
  2. Every pair returns the same set: from (E, G), (E, K), (G, ν), (G, K) and (K, ν) of steel back to E 210 GPa and ν 0.3Consistency of the isotropic relations (round trip)
  3. EN 1999-1-1 aluminium E 70 GPa, G 27 GPa gives ν = 0.2963 (the code rounds ν to 0.3)EN 1999-1-1:2007 §3.2.5; ν = E/(2G) − 1
  4. Copper C11000 data sheet: E 17 000 ksi, G 6 400 ksi gives ν = 0.328National Bronze & Metals C11000 data sheet (modulus of elasticity in tension and modulus of rigidity)
  5. Limiting cases: ν = 0 gives G = E/2 and K = E/3; ν → 0.5 makes K grow without bound and G → E/3Limits of G = E/(2(1 + ν)) and K = E/(3(1 − 2ν))
  6. Impossible pairs are refused: G below E/3, E above 9K, ν of 0.5 or more; zero E is rejectedBehaviour check: warnings and rejected inputs
  7. Worked example of the article: the calculator reproduces 80.77 GPa, 175.0 GPa, 121.2 GPa to the digits printedThe worked example on this page, to the digits printed

Assumptions and sources

Assumptions and limits

  • The material is isotropic and linear elastic, so two constants define all the others. Wood, fibre composites, rolled single crystals and many plastics are anisotropic, and these relations do not hold for them.
  • Poisson's ratio must lie between −1 and 0.5 for a stable isotropic solid; at 0.5 the material is incompressible and the bulk modulus is infinite, so the calculator refuses ν ≥ 0.5.
  • Measured E, G and ν of real alloys are often not exactly consistent with G = E/(2(1 + ν)), because they come from different tests and textured products; differences of a few per cent are normal.

Sources

  • Timoshenko and Goodier, Theory of Elasticity, 3rd ed., §3–§7 (relations between the elastic constants of an isotropic body)
  • Gere and Goodno, Mechanics of Materials, 9th ed., §3.6 (G = E/(2(1 + ν))) and §7.5 (bulk modulus K = E/(3(1 − 2ν)))
  • EN 1993-1-1:2005 §3.2.6 (steel E 210 GPa, G 81 GPa, ν 0.3); EN 1999-1-1:2007 §3.2.5 (aluminium E 70 GPa, G 27 GPa, ν 0.3)

Cite this calculator

Papandreou, C. (2026). Elastic constants calculator (E, G, K, Poisson's ratio). Engineering Bible. https://engineeringbible.com/mechanical/elastic-constants/

Embed this calculator on your site

Copy this HTML into your page. The calculator stays free to use and links back here.

By Christos Papandreou. Updated . How the numbers are checked.