Skip to content
Engineering Bible

Results appear as you type. Use the arrow keys to move through them and Enter to open one.

Popular

↑ ↓ moveEnter openEsc close

Material properties table (steel, aluminium, plastics)

Density, Young's modulus, yield and tensile strength, thermal expansion, conductivity, specific heat and melting range of common materials, with mass.

Units

Results are estimates. They do not replace the governing code, class or flag requirements, or a check by a competent person. Report a problem

Introduction

Most engineering sums start with a handful of material properties. Density gives weight, Young's modulus gives stiffness, and the yield strength sets the stress a part can carry. Structural steel S355, for example, weighs 7 850 kg/m³, has a modulus of 210 GPa and yields at 355 MPa in plates up to 40 mm thick.

This page holds those properties for twenty common materials: structural and stainless steels, aluminium alloys, copper, brass, titanium, cast iron, concrete, timber, glass and three plastics. Each value comes from a named standard or data sheet. Enter a volume to get the mass, and compare materials by their stiffness and strength per unit weight. It is for designers, students and anyone choosing a material.

Formulas

Values derived from the table:

m = ρ V
specific stiffness = E / ρ
specific strength = f / ρ
  • ρ — density; V — volume; E — Young's modulus
  • f — yield or 0.2 % proof strength, or the tensile or characteristic strength where there is no yield

Main values held (the calculator shows the thermal properties and the basis of each value):

Materialρ (kg/m³)E (GPa)Yield (MPa)Tensile (MPa)α (µm/(m·K))
S235, t ≤ 40 mm7 85021023536012.0
S355, t ≤ 40 mm7 85021035549012.0
ASTM A367 85020024840011.7
ASTM A572 Grade 507 85020034544811.7
Stainless 3048 03019320551516.9
Stainless 3168 03019320551516.0
Aluminium 6061-T62 7006927631023.6
Aluminium 6082-T62 7007026031023.0
Aluminium 5083-O2 7007012527523.0
Copper C110008 9101176922116.9
Brass C260008 53011010332420.0
Titanium Grade 24 5101052753448.6
Ti-6Al-4V4 4301148288958.6
Grey iron EN-GJL-2507 200103—250—
Concrete C30/372 40033—2.910.0
Timber C2442011—14.5—
Float glass2 50070—459.0
PVC-U1 4403.055—75
HDPE9501.123—180
Nylon PA661 1402.4838581

Assumptions and limitations

  • Steel, aluminium, concrete and timber values are code minimums or characteristic values. Copper, brass, 6061-T6 and the plastics are typical data-sheet values. The basis line in the results says which.
  • Strengths depend on thickness, temper and product form. Thicker plate, welded joints and higher temperatures all give lower values.
  • Concrete is shown with its mean tensile strength. Its compressive strength fck is 30 MPa. Timber shows its tension strength along the grain, and glass its bending strength.
  • A dash means no value from a cited source is held for that property. The page does not fill gaps with guesses.
  • Plastics creep under steady load and soften as they warm. Their short-term values overstate what they carry for years.

Worked example

A designer compares a 2 litre block of aluminium 6061-T6 with the same volume of S355 steel.

  1. Mass of the aluminium: 2 700 × 0.002 = 5.40 kg. The steel weighs 7 850 × 0.002 = 15.7 kg.
  2. Specific stiffness of the aluminium: 68.9 GPa / 2 700 = 25.52 MJ/kg. Steel gives 210 / 7 850 = 26.75 MJ/kg, almost the same.
  3. Specific strength of the aluminium: 276 MPa / 2 700 = 102.2 kJ/kg. Steel gives 355 / 7 850 = 45.2 kJ/kg.

Per kilogram, the aluminium is about as stiff as steel and more than twice as strong. Per litre, steel is three times stiffer.

FAQ

What is the density of steel?

7 850 kg/m³ for structural carbon steel in Eurocode design, about 490 lb/ft³. Stainless steels 304 and 316 are slightly heavier at 8 030 kg/m³.

What is Young's modulus of steel and aluminium?

Eurocode 3 uses 210 GPa for structural steel and AISC uses 200 GPa (29 000 ksi). Aluminium alloys are about 70 GPa, a third of steel.

What is the yield strength of A36 steel?

36 ksi, or 248 MPa, as a minimum. Its tensile strength is 58 to 80 ksi, 400 to 550 MPa.

What is the difference between 6061-T6 and 6082-T6?

Both are heat-treated Al-Mg-Si alloys of similar strength. 6061 is the common alloy in North America, 6082 in Europe.

Why does stainless steel expand more than carbon steel?

Austenitic grades such as 304 expand about 17 µm per metre per kelvin, against 12 for carbon steel. Joints between them need room to move.

Is titanium stronger than steel?

Ti-6Al-4V yields at 828 MPa or more, far above S355, and weighs 44 % less. Commercially pure Grade 2 is about as strong as S275 steel.

Related calculators

What this calculator is checked against

Before every release the calculator must reproduce each case below. The note under each case says where the expected answer comes from: a standard, a textbook, a published table, or a hand calculation shown in full.

  1. EN 1993-1-1: S235 fy 235, fu 360; S355 fy 355, fu 490 MPa (t ≤ 40 mm); E 210 GPa, α 12e-6/K, ρ 7 850 kg/m³EN 1993-1-1:2005 Table 3.1 and §3.2.6
  2. EN 1993-1-2 carbon steel at 20 °C: λ = 54 − 0.0333 × 20 = 53.33 W/(m·K), c = 439.8 J/(kg·K)EN 1993-1-2:2005 §3.4.1.2 (eq. 3.2) and §3.4.1.3 (eq. 3.4)
  3. ASTM A36 Fy 36 ksi = 248.2 MPa, Fu 58 ksi = 399.9 MPa; A572 Gr 50 Fy 50 ksi = 344.7 MPaASTM A36 and A572 minimum properties (1 ksi = 6.894757 MPa)
  4. Data-sheet values: 304 ρ 8 030, E 193 GPa, k 16.2; copper k 226 Btu·ft/(h·ft²·°F) = 391.1 W/(m·K), α 9.40 µin/(in·°F) = 16.92 µm/(m·K)Cleveland-Cliffs 304/304L bulletin; National Bronze C11000 data sheet
  5. Derived values: 2 L of 6061-T6 is 5.40 kg; E/ρ 25.52 MJ/kg; 276 MPa / 2 700 = 102.2 kJ/kg; no volume gives no massm = ρ V, E/ρ, f/ρ (by hand)
  6. Every material calculates; brittle materials use their tensile or characteristic strength; an unknown material is rejectedBehaviour check: warnings and rejected inputs
  7. Worked example of the article: the calculator reproduces 5.40 kg, 25.52 MJ/kg, 102.2 kJ/kg to the digits printedThe worked example on this page, to the digits printed

Assumptions and sources

Assumptions and limits

  • Each value comes from the standard or data sheet named with the material: code minimums or characteristic values for structural steels, aluminium (EN 1999-1-1), stainless steel (ASTM A240), concrete and timber, and typical data-sheet values for copper, brass, 6061-T6, titanium physical data and plastics. The basis line says which.
  • Strengths are room-temperature values for the product form and thickness stated; thicker sections, other tempers, welding and higher temperatures lower them. Use the mill certificate or the design code for a real design.
  • Physical properties are at about 20 °C (expansion over the range stated). A dash means no cited value is held for that property rather than a guess.
  • Mass is density × volume; specific stiffness E/ρ and specific strength f/ρ use the yield strength, or the tensile or characteristic strength where no yield is defined.

Sources

  • EN 1993-1-1:2005 Table 3.1 and §3.2.6; EN 1993-1-2:2005 §3.4.1 (thermal properties of carbon steel); EN 1999-1-1:2007 Tables 3.2a, 3.2b and §3.2.5
  • EN 1992-1-1:2004 Table 3.1 and §3.1.3; EN 1992-1-2:2004 §3.3; EN 1991-1-1 Table A.1; EN 338:2016 Table 1; EN 572-1 §6
  • ASTM A36, A572, A240, B265, B348; Cleveland-Cliffs 304/304L and 316/316L product data bulletins (2021); ASM Aerospace Specification Metals data sheets (6061-T6, Ti Grade 2, Ti-6Al-4V)
  • National Bronze & Metals C11000 and C26000 data sheets; Ensinger TECAMID 66, Angst+Pfister APSOplast PVC-U and S-Polytec PE-HD technical data sheets

Cite this calculator

Papandreou, C. (2026). Material properties table (steel, aluminium, plastics) calculator. Engineering Bible. https://engineeringbible.com/mechanical/material-properties/

Embed this calculator on your site

Copy this HTML into your page. The calculator stays free to use and links back here.

By Christos Papandreou. Updated . How the numbers are checked.