Mechanical engineering glossary
34 terms from the mechanical calculators, each in two or three sentences with its symbol, its unit and a typical value. Every entry links to the calculators that use it; the formula sheet has the equations.
-
Angle of twistθrad (°)
Also called twist angle, torsional deflection
The rotation of one end of a shaft relative to the other under torque, θ = T L / (G J) in radians. A common limit for transmission shafts is about 1° over a length of 20 diameters, and about 0.25° per metre for long line shafts. Excess twist upsets gear mesh, timing and torsional vibration behaviour.
Shaft torsion calculator (shear stress, twist, diameter), Shaft torque, power and diameter
-
Basic dynamic load ratingCkN
Also called dynamic load rating, C rating
The constant load a rolling bearing can carry for a basic rating life of one million revolutions, as listed in the maker’s catalogue under ISO 281. Life scales with (C/P) to the power 3 for ball bearings and 10/3 for roller bearings, so doubling the load cuts ball bearing life to one eighth.
-
Basic rating lifeL10million revolutions (h)
Also called L10 life, L10h, bearing life
The life that 90 % of a large group of identical rolling bearings reach or exceed before rolling contact fatigue appears. ISO 281 gives L10 = (C/P)^p million revolutions, with p = 3 for ball and 10/3 for roller bearings, and L10h = L10 × 10^6 / (60 n) hours. Lubrication and contamination enter through the modified life L_nm.
-
Bolt preloadFMkN
Also called preload, clamp load, bolt tension
The axial tension produced in a bolt by tightening, which clamps the joint members together. Targets are commonly 70 to 75 % of the proof load, or a combined tension and torsion stress of 90 % of yield under VDI 2230. Too little preload lets a joint slip, separate or work loose and exposes the bolt to fatigue.
-
Brake mean effective pressurepmebar (kPa)
Also called BMEP, mean effective pressure
The steady pressure that, acting on the pistons during each power stroke, would deliver the measured brake work; it equals brake work per cycle divided by swept volume. Naturally aspirated petrol engines reach about 10 to 13 bar, turbocharged petrol and truck diesel engines 18 to 25 bar. It compares how hard engines of different sizes are worked.
-
Carbon equivalentCE% (by mass)
Also called CEV, CE IIW, Pcm, CET
A figure that combines the hardening effect of carbon and alloying elements, used to judge the weldability of a steel and its need for preheat. The IIW formula is CE = C + Mn/6 + (Cr + Mo + V)/5 + (Ni + Cu)/15; below about 0.40 a steel usually needs no preheat, above about 0.45 it normally does.
-
Critical speedncrpm (rad/s)
Also called whirling speed, shaft whirl
The rotational speed at which a shaft runs at one of its lateral natural frequencies, so whirl deflection grows sharply. The first critical speed of a shaft with static deflection δ in mm is roughly 946/√δ rpm, and operating speed is normally kept at least 20 % away from it. Rayleigh and Dunkerley methods estimate it for stepped shafts.
Shaft critical speed calculator (Rayleigh and Dunkerley), Vibration isolation and severity
-
Endurance limitSeMPa (ksi)
Also called fatigue limit
The fully reversed stress amplitude below which a material survives an indefinitely large number of cycles. For steels the rotating-beam value is about half the tensile strength, capped near 700 MPa, and is then reduced by Marin factors for surface finish, size, loading, temperature and reliability. Aluminium alloys have no true limit.
Fatigue safety factor calculator (Goodman, Gerber, Soderberg), Material properties table (steel, aluminium, plastics)
-
Factor of safetyndimensionless
Also called safety factor, FoS, FS
The ratio of the strength or failure load of a part to the stress or load it actually carries. About 1.5 to 2 suits ductile metals under well-known static loads, 3 or more where loads, material or failure mode are uncertain, and wire rope slings commonly use 5. Limit state codes split this margin into partial factors.
Fatigue safety factor calculator (Goodman, Gerber, Soderberg), Column buckling (Euler and Johnson), Thin-wall pressure vessel, Lifting sling and wire rope load, Soil bearing capacity calculator (Terzaghi and Eurocode 7)
-
Gear ratioidimensionless
Also called speed ratio, transmission ratio
The number of teeth on the driven gear divided by the number on the driving gear, equal to input speed divided by output speed. Output torque rises by the same ratio, less mesh losses of about 1 to 2 % per spur or helical stage. A single spur or helical stage rarely exceeds about 6:1.
Gear ratio, rpm and torque, Belt and pulley calculator (ratio, rpm, belt length), Chain and sprocket calculator (roller chain length), Torque, power and speed
-
Goodman criterionnone
Also called modified Goodman, Goodman diagram, Goodman line
A fatigue failure rule for combined mean and alternating stress, drawn as a straight line from the endurance limit on the alternating axis to the ultimate tensile strength on the mean axis. The safety factor n follows from σ_a/S_e + σ_m/S_ut = 1/n; the Gerber parabola is less conservative and the Soderberg line, which uses yield strength, more so.
Fatigue safety factor calculator (Goodman, Gerber, Soderberg)
-
Hoop stressσ_θMPa (psi)
Also called circumferential stress, Barlow formula
The circumferential stress in the wall of a pressurised cylinder or pipe. For a thin wall it equals p D / (2 t), twice the longitudinal stress p D / (4 t), which is why overpressured pipes split along their length. The thin-wall formula is accurate when the diameter is more than about 20 times the wall thickness.
Thin-wall pressure vessel, Pipe wall thickness (ASME B31.3), Interference fit
-
Interference fitδµm (mm)
Also called press fit, shrink fit, force fit
A joint in which the shaft is made larger than the hub bore, so that pressing or heating the hub on leaves a contact pressure that carries torque and axial load by friction. Steel shrink fits typically use a diametral interference of about 0.05 to 0.15 % of the diameter. Contact pressure and hub stresses follow from Lamé’s thick-cylinder equations.
-
Mass moment of inertiaIkg·m²
Also called rotational inertia, MMOI
The resistance of a body to angular acceleration about an axis, the sum of each mass element times the square of its distance from the axis. A solid disc has ½ m r² and a thin ring m r²; stored kinetic energy is ½ I ω². It is not the second moment of area used for beam bending.
Mass moment of inertia calculator, Flywheel energy calculator (inertia and speed fluctuation), Shaft critical speed calculator (Rayleigh and Dunkerley)
-
Mechanical advantageMAdimensionless
The ratio of the output force of a machine to the input force applied to it. The ideal value, ignoring friction, equals input movement divided by output movement: a lever with arms in the ratio 4:1 and a pulley block with four supporting falls both give 4. The actual value is the ideal one times the efficiency.
Mechanical advantage calculator (lever, pulley, screw jack), Hydraulic cylinder force and speed, Gear ratio, rpm and torque
-
Mohr’s circlenone
Also called Mohr circle, Mohr’s stress circle
A graphical construction that plots normal stress against shear stress on every plane through a point, forming a circle centred on the mean normal stress with a radius equal to the maximum in-plane shear stress. The circle crosses the normal-stress axis at the principal stresses, and a rotation of θ on the element appears as 2θ on the circle.
-
Natural frequencyfnHz
Also called eigenfrequency, first mode frequency
The frequency at which a system vibrates freely after a disturbance, set by its stiffness and mass: f_n = (1/2π) √(k/m). For a mass on springs it is about 15.8/√δ Hz with the static deflection δ in mm. Excitation close to it causes resonance, so machine running speeds are kept clear of it.
Vibration isolation and severity, Shaft critical speed calculator (Rayleigh and Dunkerley), Spring rate calculator (helical compression spring)
-
Nut factorKdimensionless
Also called torque coefficient, K factor
An empirical coefficient relating tightening torque to bolt preload through T = K F d, where d is the nominal bolt diameter. It is about 0.20 for plain dry steel, 0.15 to 0.18 lightly oiled and 0.10 to 0.12 with molybdenum disulfide paste. Around 90 % of the torque is lost in friction, so lubrication changes preload greatly.
-
Poisson’s ratioνdimensionless
Also called Poisson ratio
The ratio of lateral contraction strain to axial extension strain in a material under uniaxial stress within the elastic range. Steel is about 0.30, aluminium 0.33, concrete 0.15 to 0.20 and rubber close to 0.5. For isotropic materials it links the elastic constants through G = E / (2 (1 + ν)).
Elastic constants calculator (E, G, K, Poisson's ratio), Stress and strain calculator (Young's modulus), Interference fit, Material properties table (steel, aluminium, plastics)
-
Polar moment of inertiaJmm⁴ (in⁴)
Also called polar second moment of area
A cross-section property measuring resistance to torsion, the integral of r² over the area. A solid round shaft has J = π d⁴ / 32 and a tube π (D⁴ − d⁴) / 32; surface shear stress is T r / J and the angle of twist T L / (G J). These formulas hold only for circular sections.
Shaft torsion calculator (shear stress, twist, diameter), Shaft torque, power and diameter
-
Principal stressσ1MPa (psi)
Also called principal stresses, maximum normal stress
The normal stresses on the planes through a point where shear stress is zero, which are the largest and smallest normal stresses at that point. In plane stress they are (σx + σy)/2 ± √(((σx − σy)/2)² + τxy²). Brittle materials fail when the largest one reaches the tensile strength.
-
S-N curvenone
Also called Wöhler curve, fatigue curve, SN curve
A plot of stress amplitude or range against the number of cycles to failure, normally on logarithmic axes. Curves for steel flatten near 10^6 to 10^7 cycles, while weld design curves such as those of DNV-RP-C203 or the Eurocode 3 detail categories sit about two standard deviations below the mean test data. Miner’s rule extends it to variable loading.
Fatigue safety factor calculator (Goodman, Gerber, Soderberg), Weld fatigue damage (DNV-RP-C203)
-
Shear modulusGGPa
Also called modulus of rigidity, modulus of elasticity in shear
The ratio of shear stress to shear strain in the elastic range, which governs the twist of shafts and the rate of coil springs. Steel is about 79 to 81 GPa and aluminium alloys about 26 GPa; for isotropic materials G = E / (2 (1 + ν)).
Elastic constants calculator (E, G, K, Poisson's ratio), Shaft torsion calculator (shear stress, twist, diameter), Spring rate calculator (helical compression spring), Material properties table (steel, aluminium, plastics)
-
Spring ratekN/mm (lbf/in)
Also called spring constant, spring stiffness
The force needed to deflect a spring by unit distance. For a helical compression spring k = G d⁴ / (8 D³ N_a), with wire diameter d, mean coil diameter D and active coils N_a, so the rate rises with the fourth power of wire size. Counting the inactive end coils as active is a common error.
Spring rate calculator (helical compression spring), Vibration isolation and severity
-
Strainεdimensionless (µε)
Also called engineering strain, microstrain
The relative deformation of a material; for normal strain, the change in length divided by the original length. Structural steel reaches yield at a strain of about 0.12 % (1200 microstrain), while elongation at fracture in a tensile test is 20 % or more. Strain gauges measure it directly, and stress follows from Young’s modulus in the elastic range.
Stress and strain calculator (Young's modulus), Elastic constants calculator (E, G, K, Poisson's ratio)
-
StressσMPa (psi)
Also called normal stress, shear stress
The internal force per unit area acting on a plane within a loaded body: normal stress acts perpendicular to the plane and shear stress along it. For a bar in tension it is the load divided by the cross-section area, and 1 MPa equals 1 N/mm². Comparing it with yield or fatigue strength gives the factor of safety.
Stress and strain calculator (Young's modulus), Mohr's circle calculator (principal stress, von Mises), Shaft torsion calculator (shear stress, twist, diameter), Beam deflection and bending stress
-
Stress concentration factorKtdimensionless
Also called SCF, Kt, notch factor
The ratio of the peak local stress at a hole, notch or fillet to the nominal stress in the section. A small round hole in a wide plate under tension gives 3.0. In fatigue the effective factor is lower, K_f = 1 + q (K_t − 1), where q is the notch sensitivity of the material.
Fatigue safety factor calculator (Goodman, Gerber, Soderberg), Weld fatigue damage (DNV-RP-C203)
-
Tolerance stack-upmm (in)
Also called tolerance analysis, tolerance stacking, RSS tolerance
The accumulation of individual dimensional tolerances along a chain of parts, which sets the variation of a gap or assembly dimension. Worst case adds the tolerances directly; root sum of squares takes the square root of the summed squared tolerances, giving a narrower, statistically likely range. RSS assumes independent, centred, normally distributed dimensions.
-
TorqueTN·m (lbf·ft)
Also called turning moment
The turning effect of a force about an axis, equal to the force times its perpendicular distance from the axis. Shaft power is torque times angular speed, so P in kW = T in N·m × rpm / 9549. Gearing trades speed for torque at nearly constant power.
Torque, power and speed, Shaft torque, power and diameter, Gear ratio, rpm and torque, Bolt torque and preload, Engine BMEP, torque and power
-
TransmissibilityTdimensionless
Also called force transmissibility, isolation efficiency
The ratio of the force transmitted through an isolator to the force applied, or of output to input vibration amplitude. Isolation begins only above a frequency ratio of √2; at a ratio of 3 an undamped mount transmits 12.5 %, an isolation efficiency of 87.5 %. Below √2 the mounts amplify vibration.
-
Ultimate tensile strengthRmMPa (ksi)
Also called UTS, tensile strength, S_ut
The maximum engineering stress a material sustains in a tensile test, the peak load divided by the original cross-section area. Mild steel is about 400 to 550 MPa and 6061-T6 aluminium about 310 MPa. For steels it can be estimated as roughly 3.4 times the Brinell hardness, in MPa.
Material properties table (steel, aluminium, plastics), Fatigue safety factor calculator (Goodman, Gerber, Soderberg), Hardness conversion calculator (HRC, HRB, HV, HB), Bolt torque and preload
-
Von Mises stressσvMMPa (psi)
Also called equivalent stress, distortion energy criterion, von Mises criterion
A scalar equivalent stress that combines all stress components to predict yielding of ductile metals under multiaxial loading. In plane stress it is √(σ1² − σ1 σ2 + σ2²), and under pure shear it equals √3 times the shear stress, so shear yield is about 0.577 times tensile yield.
Mohr's circle calculator (principal stress, von Mises), Interference fit
-
Yield strengthReMPa (ksi)
Also called yield stress, proof stress, R_p0.2, S_y
The stress at which a material begins to deform plastically; where no distinct yield point exists, the 0.2 % offset proof stress R_p0.2 is used. Structural steels S235 and S355 have minimum values of 235 and 355 MPa at thicknesses up to 16 mm. Most static designs keep working stress below yield with a safety margin.
Material properties table (steel, aluminium, plastics), Stress and strain calculator (Young's modulus), Bolt torque and preload, Thin-wall pressure vessel, Column buckling (Euler and Johnson)
-
Young’s modulusEGPa (Msi)
Also called modulus of elasticity, elastic modulus, E-modulus
The ratio of normal stress to normal strain in the linear elastic range, the slope of the initial straight part of the stress–strain curve. Steel is about 200 to 210 GPa, aluminium alloys about 70 GPa and concrete 25 to 40 GPa. It sets stiffness and deflection, not strength, so a stronger steel does not deflect less.
Stress and strain calculator (Young's modulus), Elastic constants calculator (E, G, K, Poisson's ratio), Material properties table (steel, aluminium, plastics), Beam deflection and bending stress
Results are estimates. They do not replace the governing code, class or flag requirements, or a check by a competent person.