Manufacturing and machining practice problems
10 multiple-choice problems in the style of the FE and PE engineering exams. Pick an answer to check it, then open the worked solution. Every answer is recomputed by the manufacturing and machining calculator that solves it, and the solution opens that calculator with the problem's numbers filled in.
-
Flat blank length of a sheet steel channel
A U-channel is formed on a press brake from 2.0 mm steel sheet. Its outside dimensions are 40 mm, 60 mm and 40 mm, with two 90° bends at an inside radius of 3.0 mm. Test bends on this material give a K-factor of 0.40. What flat blank length must be cut?
Show the answer and worked solution
Answer: C, 131.9 mm
- Bend allowance per bend: BA = θ (R + K T) = (π / 2) × (3.0 + 0.40 × 2.0) = 5.97 mm.
- Outside setback: OSSB = tan(θ / 2) × (R + T) = 1 × 5.0 = 5.0 mm, so the bend deduction is BD = 2 × OSSB − BA = 4.03 mm.
- Flat length: L = 40 + 60 + 40 − 2 × 4.03 = 131.9 mm.
- The traps: 140.0 mm adds the outside dimensions with no deduction, 151.9 mm adds the two bend allowances to the outside dimensions, and 120.0 mm subtracts both setbacks at each bend but forgets to add back the bend allowance.
Check every step: Bend allowance calculator (sheet metal flat length), opened with this problem’s numbers
-
Feed rate for a light radial cut with chip thinning
A 10 mm four-flute carbide end mill runs at 8000 rpm with a radial width of cut of 1.0 mm. The tool maker recommends a maximum chip thickness of 0.050 mm per tooth. Allowing for radial chip thinning, what table feed rate should be programmed?
Show the answer and worked solution
Answer: A, 2670 mm/min
- Radial engagement: a_e / D = 1.0 / 10 = 0.10, below 0.5, so the chip is thinner than the feed per tooth.
- Chip thinning factor: RCTF = 1 / √(1 − (1 − 2 a_e / D)²) = 1 / √(1 − 0.8²) = 1.667.
- Programmed feed per tooth: f_z = 0.050 × 1.667 = 0.0833 mm.
- Feed rate: v_f = f_z × z × n = 0.0833 × 4 × 8000 = 2670 mm/min.
- The traps: 1600 mm/min ignores chip thinning, 960 mm/min divides by the thinning factor instead of multiplying, and 667 mm/min forgets the four flutes.
Check every step: Chip load calculator with chip thinning, opened with this problem’s numbers
-
Theoretical Ra of a turned finish
A finishing pass on a steel shaft uses a turning insert with a 0.8 mm nose radius at a feed of 0.20 mm/rev. Assuming the ideal profile left by the nose radius, what is the theoretical arithmetic mean roughness Ra of the turned surface?
Show the answer and worked solution
Answer: D, 1.60 µm
- Peak-to-valley height of the ideal profile: R_t = f² / (8 r) = 0.20² / (8 × 0.8) = 0.00625 mm = 6.25 µm.
- Arithmetic mean: Ra = f² / (18√3 r) = 0.04 / (31.18 × 0.8) = 0.00160 mm = 1.60 µm.
- The traps: 6.25 µm is R_t, not Ra; 3.21 µm reads 0.8 mm as the nose diameter and uses r = 0.4 mm; 1.78 µm is the RMS value Rq ≈ 1.11 Ra.
Check every step: Surface finish converter (Ra, RMS, Rz, N grades), opened with this problem’s numbers
-
Metal removal rate of a face mill
A 63 mm face mill with 5 inserts machines a steel block at a cutting speed of 200 m/min and a feed of 0.12 mm per tooth. The axial depth of cut is 2.0 mm and the width of cut is 40 mm. What is the metal removal rate?
Show the answer and worked solution
Answer: B, 48.5 cm³/min
- Spindle speed: n = v_c / (π D) = 200 000 / (π × 63) = 1010 rpm.
- Table feed: v_f = f_z × z × n = 0.12 × 5 × 1010 = 606 mm/min.
- Removal rate: MRR = a_p × a_e × v_f = 2.0 × 40 × 606 = 48 500 mm³/min = 48.5 cm³/min.
- The traps: 9.7 cm³/min forgets the 5 inserts, 76.4 cm³/min takes the full cutter diameter of 63 mm as the width of cut, and 97.0 cm³/min puts the radius into n = v_c / (π D) and so doubles the speed.
Check every step: Speeds and feeds calculator (milling, turning, drilling), opened with this problem’s numbers
-
Press load to punch four holes in steel plate
A press tool punches four 22 mm holes per stroke in 6.0 mm steel plate with an ultimate tensile strength of 430 MPa. Take the shear strength as 0.75 of the tensile strength and allow 10 % of the punching force for stripping. What is the total load on the press?
Show the answer and worked solution
Answer: C, 588 kN
- Shear strength: τ = 0.75 × 430 = 322.5 MPa.
- Punching force: F = n π d t τ = 4 × π × 22 × 6.0 × 322.5 = 535 kN.
- With stripping: 1.10 × 535 = 588 kN.
- The traps: 535 kN leaves out the stripping force, 785 kN uses the tensile strength as the shear strength, and 294 kN takes the cut perimeter as π r instead of π d.
Check every step: Press tonnage calculator (punching and press brake), opened with this problem’s numbers
-
Clamp rating for a four-cavity injection mould
A four-cavity mould makes polypropylene lids. Each lid has a projected area of 85 cm² and the cold runner adds 30 cm². The mean cavity pressure is estimated at 35 MPa. The plant runs its presses at no more than 80 % of their rated clamp force. What is the smallest machine clamp rating to choose?
Show the answer and worked solution
Answer: A, 1.62 MN
- Projected area: A = 4 × 85 + 30 = 370 cm² = 0.0370 m².
- Clamp force: F = A × p = 0.0370 × 35 × 10⁶ = 1.295 MN.
- Machine rating at 80 % use: 1.295 / 0.80 = 1.62 MN.
- The traps: 1.30 MN is the clamp force with no margin, 1.04 MN multiplies by 0.80 instead of dividing, and 1.49 MN leaves out the runner area.
Check every step: Injection molding clamp tonnage calculator, opened with this problem’s numbers
-
Cutting time to drill a blind hole
A 12 mm twist drill with a 118° point drills a blind hole 30 mm deep at full diameter. The spindle runs at 700 rpm with a feed of 0.20 mm/rev, and the approach clearance is 2.0 mm. How long does the drill cut for each hole?
Show the answer and worked solution
Answer: D, 15.3 s
- Point length: l_p = D / (2 tan(θ / 2)) = 12 / (2 × tan 59°) = 3.6 mm.
- Feed travel: L = 30 + 3.6 + 2.0 = 35.6 mm.
- Feed rate: v_f = f × n = 0.20 × 700 = 140 mm/min, so t = 35.6 / 140 = 0.254 min = 15.3 s.
- The traps: 13.7 s leaves out the point length, 12.9 s leaves out both the point and the approach, and 7.6 s doubles the feed by counting it per cutting lip of the two-lip drill.
Check every step: Machining time calculator (turning, facing, drilling, milling), opened with this problem’s numbers
-
OEE of a moulding cell over one shift
A moulding cell works an 8 h shift with 45 min of planned breaks. During the shift it loses 50 min to breakdowns and changeovers. The ideal cycle time is 30 s per part. The cell makes 680 parts, of which 17 are rejected. Customer demand is 600 parts per shift. What is the overall equipment effectiveness (OEE)?
Show the answer and worked solution
Answer: B, 76.2 %
- Planned time: 480 − 45 = 435 min; run time: 435 − 50 = 385 min.
- Availability = 385 / 435 = 0.885; performance = 680 × 30 s / (385 × 60 s) = 0.883; quality = 663 / 680 = 0.975.
- OEE = 0.885 × 0.883 × 0.975 = 0.762 = 76.2 %, the same as good parts × ideal cycle / planned time = 663 × 30 / 26 100 s.
- The traps: 69.1 % divides by the whole 8 h shift instead of the planned time, 78.2 % counts all 680 parts as good, and 86.3 % multiplies availability and quality but forgets performance.
Check every step: OEE and takt time calculator, opened with this problem’s numbers
-
Tap drill for an M12 thread at 65 % thread engagement
An M12 × 1.75 coarse thread is to be tapped in a tough stainless steel. To cut the tapping torque, the shop runs 65 % of full thread instead of the usual 75 %. Using the tap makers' rule, in which 100 % thread is a double thread depth of 1.299 P, what theoretical tap drill diameter is needed?
Show the answer and worked solution
Answer: C, 10.52 mm
- Drill for a percentage of thread: d = D − 1.299 P × (% thread / 100).
- d = 12 − 1.299 × 1.75 × 0.65 = 12 − 1.48 = 10.52 mm.
- The traps: 10.25 mm is the D − P rule of thumb, which gives about 77 % thread; 10.11 mm is the basic minor diameter D − 1.0825 P, about 83 % thread; 10.77 mm applies the 65 % to 1.0825 P instead of to 1.299 P.
Check every step: Tap drill size calculator (metric and UNC/UNF), opened with this problem’s numbers
-
Covered electrodes needed for a fillet weld run
A fabricator welds 12 m of 8 mm equal-leg fillet weld on a steel frame with covered electrodes (SMAW). Allow 10 % extra weld metal for convexity, take the weld metal density as 7850 kg/m³ and the deposition efficiency of the electrodes as 55 %. What mass of electrodes must be issued?
Show the answer and worked solution
Answer: A, 6.03 kg
- Weld section: A = 1.10 × z² / 2 = 1.10 × 8² / 2 = 35.2 mm².
- Weld metal: m = A × L × ρ = 35.2 × 10⁻⁶ × 12 × 7850 = 3.32 kg.
- Electrodes: 3.32 / 0.55 = 6.03 kg.
- The traps: 3.32 kg is the deposited metal with no allowance for stub ends, slag and spatter, 12.06 kg takes the section as z² instead of z² / 2, and 1.82 kg multiplies by the efficiency instead of dividing.
Check every step: Weld metal and filler consumption calculator, opened with this problem’s numbers
Results are estimates. They do not replace the governing code, class or flag requirements, or a check by a competent person.