Pressure units explained: bar, psi, kPa, MPa and atm
Pressure is the quantity engineers convert most often and get wrong most often. A pump data sheet gives head in metres, the gauge on the discharge reads bar, the relief valve is stamped in psi, the pipe material is rated in MPa and the old compressor in the corner has a dial in kgf/cm². All of them measure the same thing, force per unit area, and all of them convert with fixed factors.
Two different things go wrong. The first is the factor: bar, atmosphere and kgf/cm² are within 3 % of one another, close enough to be confused and far enough apart to matter. The second is the reference: a gauge reads pressure above the surrounding air, while gas laws, vapour pressures and suction calculations need pressure above a vacuum. The second mistake is usually the larger one.
This guide gives the definitions, a table of factors, the rule for moving between gauge and absolute pressure, the link between pressure and a height of liquid, and the shortcuts that are safe to use in your head. Every factor here is the one used by the pressure converter and by every calculator on the site.
Pressure and the pascal
Pressure is force divided by the area it acts on. The SI unit is the pascal: one newton on one square metre.
p = F ÷ A
1 Pa = 1 N/m²
A pascal is tiny, so practical work uses multiples: the kilopascal (kPa, 1000 Pa), the megapascal (MPa, 10⁶ Pa) and the gigapascal (GPa, 10⁹ Pa). Stress in a solid is also force per area and uses the same units, which is why the converter lists pressure and stress as one quantity.
One megapascal is one newton per square millimetre. MPa and N/mm² are the same unit written two ways, and no factor is needed between them.
Where you meet each unit
- bar: process plant, hydraulics, compressed air, boilers and ship systems in most of the world. A 250 bar hydraulic system is 25 MPa, or 3626 psi.
- psi (pound-force per square inch): the everyday unit in the United States and on much British and American equipment. A tyre at 32 psi is at 2.21 bar, or 221 kPa.
- kPa: the SI unit for moderate pressures: tyre placards, ventilation, weather and the inputs of most calculators here.
- MPa and ksi: material strength and high-pressure equipment. A steel with a yield strength of 355 MPa is a 51.5 ksi steel; 36 ksi is 248 MPa and 50 ksi is 345 MPa. One ksi is 1000 psi.
- kgf/cm² (kilogram-force per square centimetre): gauges on older machinery and on equipment from countries that used the metric technical system. It is close to the bar but not equal to it.
- atm (standard atmosphere): a reference condition for gases and for diving, rarely the scale of a gauge.
- mmHg, inHg and mbar: barometers, weather and vacuum. The standard atmosphere is 1013.25 mbar, 760 mmHg or 29.92 inHg. A millibar and a hectopascal (hPa) are the same thing.
- metres or feet of water: pump head, tank levels and low pressures in ducts and burners (millimetres or inches of water column).
Exact definitions and conversion factors
Four definitions fix everything else:
- 1 bar = 100 000 Pa exactly, so 1 bar = 100 kPa = 0.1 MPa, and 1 mbar = 100 Pa.
- 1 atm = 101 325 Pa exactly: the sea-level pressure of the standard atmosphere (ISO 2533).
- 1 psi = 6894.757 Pa: one pound-force (4.4482216 N) on one square inch (25.4 mm × 25.4 mm).
- 1 kgf/cm² = 98 066.5 Pa exactly: one kilogram-force (9.806 65 N) on one square centimetre.
The millimetre of mercury is taken as 133.3224 Pa and the metre of water as 9806.65 Pa, the pressure under one metre of water of density 1000 kg/m³ at standard gravity. These are the values of NIST Special Publication 811, Appendix B, which the unit converter follows.
| One of these | kPa | bar | psi | atm |
|---|---|---|---|---|
| 1 kPa | 1 | 0.01 | 0.1450377 | 0.009869233 |
| 1 MPa | 1000 | 10 | 145.0377 | 9.869233 |
| 1 bar | 100 | 1 | 14.50377 | 0.9869233 |
| 1 psi | 6.894757 | 0.06894757 | 1 | 0.06804596 |
| 1 atm | 101.325 | 1.01325 | 14.69595 | 1 |
| 1 kgf/cm² | 98.0665 | 0.980665 | 14.22334 | 0.9678411 |
| 1 mmHg | 0.1333224 | 0.001333224 | 0.01933678 | 0.00131579 |
| 1 m of water | 9.80665 | 0.0980665 | 1.422334 | 0.09678411 |
To convert, multiply by the factor in the row of the unit you have and the column of the unit you want. Seven bar is 7 × 14.50377 = 101.5 psi. One hundred psi is 100 × 0.06894757 = 6.895 bar. Ten kgf/cm² is 9.807 bar or 142.2 psi, while ten bar is 145.0 psi. The common pairs have their own pages with tables: bar to psi, psi to bar, kPa to psi, MPa to psi and kgf/cm² to psi.
Gauge, absolute and differential pressure
A pressure value means nothing until you know what it is measured from.
- Absolute pressure is measured from a perfect vacuum. It cannot be negative.
- Gauge pressure is measured from the surrounding atmosphere. An ordinary pressure gauge open to the air reads zero, and a partial vacuum reads negative.
- Differential pressure is the difference between two points, for example across a filter, an orifice or a length of pipe. It is the same whichever reference the two readings share.
p_abs = p_gauge + p_atm
The notation puts the reference in the unit: bar g or barg for gauge and bar a or bara for absolute; psig and psia in US practice. A bare "bar" or "psi" on a gauge or a nameplate is almost always gauge. A bare "kPa" in a steam table, a vapour pressure table or a gas calculation is almost always absolute. When a document does not say, find out before using the number.
The atmospheric term is the local pressure at the time, not a constant. At sea level the standard value is 101.325 kPa (1.01325 bar, 14.696 psi), and it falls by about 1.2 kPa for every 100 m of altitude near sea level; the standard atmosphere table gives the pressure at any height.
Worked example: a gauge reading to absolute
The gauge on a compressed-air receiver at sea level reads 7 bar. The receiver holds 0.5 m³ and the air is at 20 °C. What is the absolute pressure, and how much air is inside?
- Absolute pressure: 7 + 1.01325 = 8.01325 bar a, which is 801.325 kPa.
- In US units the same reading is 7 × 14.50377 = 101.53 psig. Adding one atmosphere, 14.70 psi, gives 116.22 psia.
- Mass of air from the ideal gas law, m = P V M ÷ (R T), with P = 801 325 Pa and T = 293.15 K: 4.76 kg, at a density of 9.52 kg/m³.
- The same calculation with the gauge value entered by mistake, P = 700 000 Pa, gives 4.16 kg. That is 13 % low.
The ideal gas law calculator reproduces steps 3 and 4: solve for the amount of gas with air, 801.325 kPa, 0.5 m³ and 20 °C. The error from using gauge pressure grows as the pressure falls. At 1 bar g the absolute pressure is about double the gauge reading.
Pressure as a head of liquid
A still liquid presses on whatever is below it with the weight of the column above. The gauge pressure at depth h in a liquid of density ρ is (White, Fluid Mechanics, hydrostatic pressure distribution):
p_gauge = ρ × g × h
p_abs = p_surface + ρ × g × h
g = 9.806 65 m/s²
Turned round, any pressure can be stated as the height of liquid that would produce it: h = p ÷ (ρ g). That height is the head. Pump makers quote head because a centrifugal pump lifts any liquid to about the same height, while the pressure it produces depends on the liquid's density. The units "metre of water" and "millimetre of mercury" are heads of an agreed liquid: 1 m of water is 9.80665 kPa, and one standard atmosphere is 10.33 m of water or 760 mmHg.
Worked example: pressure at the bottom of a tank
A gauge is fitted at the base of a fresh-water tank, 12 m below the free surface. The water is at 20 °C (ρ = 998.2 kg/m³) and the tank is vented.
- Gauge pressure: 998.2 × 9.806 65 × 12 = 117 468 Pa = 117.5 kPa.
- In other units: 117.5 kPa is 1.175 bar, 17.04 psi or 1.198 kgf/cm².
- Absolute pressure: 117.468 + 101.325 = 218.8 kPa, or 2.188 bar a.
- Head in metres of water at the conventional 1000 kg/m³: 117 468 ÷ (1000 × 9.806 65) = 11.98 m, a little under the true 12 m because the water at 20 °C is lighter than the conventional figure.
The hydrostatic pressure calculator gives the same figures for 12 m of fresh water at 20 °C. Change the liquid to heavy fuel oil at 50 °C (970 kg/m³) and 8 m of depth, and the gauge pressure is 76.1 kPa, equal to only 7.76 m of water. A level gauge calibrated in metres of water reads wrong on any other liquid by the ratio of the densities.
The formula assumes a still liquid of uniform density and standard gravity. Local gravity varies by up to 0.3 % with latitude and height, and water compresses by about 0.5 % per 1000 m of depth, so deep-ocean pressures are slightly understated. For a liquid that is moving, the pressure also changes with velocity, which is the subject of the Bernoulli calculator.
Quick mental conversions and their error
These are good enough to check a reading or catch a slipped decimal point. The error is against the exact factor.
| Shortcut | Exact factor | Error of the shortcut |
|---|---|---|
| bar × 14.5 = psi | 14.50377 | 0.03 % low |
| MPa × 145 = psi | 145.0377 | 0.03 % low |
| bar × 15 = psi | 14.50377 | 3.4 % high |
| psi × 7 = kPa; ksi × 7 = MPa | 6.894757 | 1.5 % high |
| 1 kgf/cm² = 1 bar | 0.980665 bar | 2.0 % high |
| 1 atm = 1 bar | 1.01325 bar | 1.3 % low |
| 10 m of water = 1 bar | 0.980665 bar | 2.0 % high |
| mmHg × 4/3 = mbar | 1.333224 | 0.01 % high |
| 1 psi = 2.31 ft of water | 2.306659 | 0.1 % high |
Bar to kPa (× 100) and bar to MPa (÷ 10) are exact. A shortcut with a 2 % error is fine for judging whether a reading is plausible. It is not fine for setting a relief valve, writing a test pressure or converting a material strength: use the exact factor there.
Common mistakes
- Treating bar and atm as equal. One atmosphere is 1.01325 bar. The 1.3 % rarely matters on a gauge, but "standard conditions" for a gas volume depend on which one the document means.
- Reading a kgf/cm² dial as bar. The dial reads 2 % higher in number than the same pressure in bar: 10 kgf/cm² is 9.807 bar. On a hydraulic test near a limit, 2 % is the margin.
- Converting MPa to N/mm². They are identical. Applying any factor here is the error.
- psi against ksi. Material data in ksi is a thousand times the psi figure. A 50 ksi steel is 50 000 psi, 345 MPa.
- Gauge pressure in a gas law. Boyle's law, the ideal gas law and compression ratios need absolute pressure and absolute temperature. The worked example above was 13 % out; a compression ratio taken from gauge readings is worse.
- Mixing references in a suction calculation. Vapour pressure is always absolute. Net positive suction head uses the absolute pressure on the liquid surface, atmospheric plus any gauge pressure in the vessel, as the Hydraulic Institute definition has it. For cold water in an open tank that atmospheric term is worth about 10 m of head, so leaving it out, or subtracting an absolute vapour pressure from a gauge pressure, changes the answer completely. The NPSH calculator asks for the atmospheric pressure and the vessel gauge pressure separately for this reason.
- Assuming sea-level atmosphere. Converting gauge to absolute with 101.325 kPa at altitude overstates the absolute pressure.
- Using a head without the density. Forty-five metres of head is 4.41 bar (64.0 psi) only for water at 1000 kg/m³. For any other liquid, multiply by its density ratio.
- Adding a reference to a difference. A pressure drop is a difference and carries no "gauge" or "absolute". Never add an atmosphere to it.
Which reference each calculation needs
- Strength of a pipe, vessel or hose: the difference between inside and outside, which for equipment standing in air is the gauge pressure.
- Gas mass, density and volume: absolute, always.
- Boiling, flashing and cavitation: absolute, compared with the vapour pressure.
- Friction loss in a pipe: a differential, so the reference drops out. The pipe pressure drop calculator returns a drop that you subtract from the upstream pressure in whichever reference you are working. For a gas, the incompressible method holds only while the drop stays below about 10 % of the absolute pressure.
- Bernoulli between two points: either reference, as long as both points use the same one. Only the cavitation check needs absolute.
The habit that prevents nearly all of these errors is simple to state: write the reference next to every pressure in a calculation, convert everything to one unit before combining anything, and convert back at the end. More conversions for other quantities are on the converters page, and the formulas used here are collected in the fluids formula sheet.
Calculators used in this guide
- GeneralEngineering unit converterConvert pressure, torque, power, flow, length, mass, speed, temperature, energy and marine units (knots, nautical miles, long tons) from one table.
- Fluids and pumpsHydrostatic pressure at depthGauge and absolute pressure at a depth in water, sea water, fuel or any liquid, its head in metres of water, and the force on a flat surface.
- ThermalIdeal gas law (PV = nRT)Pressure, volume, temperature or amount of a gas from PV = nRT, with its mass, density and specific gas constant for air, N₂, CO₂, H₂ and more.
- Fluids and pumpsPump NPSH and suction liftNPSH available from suction conditions, vapour pressure and losses, margin against NPSH required and the maximum suction lift.
- Fluids and pumpsPipe flow and pressure dropVelocity, Reynolds number, Darcy friction factor (Colebrook, Swamee–Jain) and pressure drop for a straight pipe with fittings.
- Fluids and pumpsBernoulli's equation and venturiPressure at a second point from Bernoulli's equation, with velocity from the bores (venturi, reducer, nozzle), height change and head loss.
Results are estimates. They do not replace the governing code, class or flag requirements, or a check by a competent person. Report an error in this guide
More guides
- Cargo securing calculation to CSS Code Annex 13
- How to do a draft survey calculation, step by step
- How EU ETS and FuelEU Maritime costs are calculated
- How much concrete do I need? Slabs, footings and posts
- How to calculate a ship's CII rating, step by step
- Hull and propeller performance in service with ISO 19030