Skip to content
Engineering Bible

Results appear as you type. Use the arrow keys to move through them and Enter to open one.

Popular

↑ ↓ moveEnter openEsc close

Manufacturing and machining formulas

The formulas behind the 12 manufacturing and machining calculators, on one page you can print or save as a PDF. Each block lists its variables and standard; the heading opens the calculator, with its assumptions and a worked example.

Belt conveyor speed and capacity calculator

Belt speed:

v = π × D × n

Load cross-section (CEMA standard area):

c = 0.055 b + 0.9 in            edge distance on each side
b' = b − 2c                     loaded belt width
s = (b' − l) / 2,  W = l + 2 s cos λ
A_base = (l + W) / 2 × s sin λ
A_surcharge = R² (β − sin β cos β),  R = W / (2 sin β)

Capacity and lift power:

Q = (A_base + A_surcharge) × v × ρ
P_lift = Q × g × H
  • D — drive pulley diameter over lagging; n — pulley speed
  • b — belt width; l — centre roll length (b/3 by default); λ — trough angle; β — surcharge angle
  • ρ — bulk density; H — lift height; g = 9.81 m/s²
  • A flat belt has λ = 0 and carries only the surcharge segment over the loaded width

Bend allowance calculator (sheet metal flat length)

One bend, with the bend angle θ in radians:

BA = θ × (R + K × T)
OSSB = tan(θ/2) × (R + T)
BD = 2 × OSSB − BA

Flat length from outside dimensions (legs measured to the mould lines):

L_flat = Σ legs − Σ BD

K-factor suggested by DIN 6935:

k = 0.65 + 0.5 × log10(R/T)   for R/T < 5,   k = 1 above
K = k / 2
  • T — sheet thickness; R — inside bend radius; θ — bend angle (90° for an L)
  • K — position of the neutral axis from the inside surface, as a fraction of T
  • BA — bend allowance; OSSB — outside setback; BD — bend deduction

Chip load calculator with chip thinning

Chip load and feed rate:

f_z = v_f / (z × n)
v_f = f_z × z × n

Radial chip thinning, for a_e below D/2:

RCTF = 1 / √(1 − (1 − 2 a_e / D)²)
h_ex = f_z / RCTF
programmed f_z = target chip × RCTF

Engagement angle:

φ = arccos(1 − 2 a_e / D)
  • v_f — feed rate; z — number of flutes; n — spindle speed in rpm
  • f_z — feed per tooth (chip load); h_ex — maximum chip thickness
  • a_e — radial depth of cut (stepover); D — cutter diameter
  • At a_e = D/2 or more, RCTF = 1 and the chip equals the feed per tooth

Drill point length calculator

Point length:

L_p = (D / 2) / tan(θ / 2)

Common point angles:

118°:  L_p = 0.3004 D
135°:  L_p = 0.2071 D
140°:  L_p = 0.1820 D

Depth to drill:

blind hole:    tip depth = full-diameter depth + L_p
through hole:  travel = thickness + L_p + breakthrough
  • D — drill diameter; θ — included point angle
  • A 180° flat-bottom drill has no point

Injection molding clamp tonnage calculator

Projected area and clamp force:

A = n × A_cavity + A_runner
F = A × p

Machine size:

rating ≥ F / u

Units of the clamp factor:

1 US ton/in² = 2 000 psi = 13.79 MPa = 1.38 kN/cm²
  • n — number of cavities; A_cavity — projected area of one part; A_runner — projected area of a cold runner
  • p — clamp factor, the mean cavity pressure over the projected area
  • u — highest share of the machine rating to use, 80 % by default

Machining time calculator (turning, facing, drilling, milling)

Feed rate:

turning, facing, drilling:  v_f = f × n
milling:                    v_f = f_z × z × n

Tool travel per pass:

turning, milling:  L_t = L + approach and overtravel
facing:            L_t = (D − d) / 2 + approach
drilling:          L_t = depth + D / (2 tan(θ/2)) + approach

Times:

t_pass = L_t / v_f
t_part = passes × t_pass
t_job = set-up + parts × (t_part + handling)
  • f — feed per revolution; f_z — feed per tooth; z — number of teeth; n — spindle speed
  • L — length of cut; D — outside or drill diameter; d — bore diameter; θ — drill point angle

OEE and takt time calculator

Times:

planned production time = shift − planned stops
run time = planned production time − downtime

OEE:

availability A = run time / planned production time
performance P = ideal cycle time × total count / run time
quality Q = good count / total count
OEE = A × P × Q = ideal cycle time × good count / planned production time

Takt time:

takt = planned production time / demand
  • Planned stops: breaks, meals and planned maintenance
  • Downtime: breakdowns, changeovers and other unplanned stops
  • Ideal cycle time: the fastest cycle the machine can sustain

Press tonnage calculator (punching and press brake)

Punching and blanking:

F = L × t × τ
τ ≈ k × UTS     (k ≈ 0.75 for steel, 0.65 for aluminium)
press load = F × (1 + s)
press capacity = press load × (1 + margin)

Press brake air bending (US units):

tons per foot = 575 × t² / V × UTS / 60 000 psi
  • L — cut perimeter (π d for a round hole); t — thickness; τ — ultimate shear strength
  • UTS — ultimate tensile strength; s — stripping force as a share of F
  • V — V-die opening in inches; t in inches; tons are US tons of 2 000 lbf

Speeds and feeds calculator (milling, turning, drilling)

Spindle speed from the cutting speed:

n = v_c / (π D)
n [rpm] = 12 × v_c [sfm] / (π × D [in]) ≈ 3.82 × v_c / D
n [rpm] = 1000 × v_c [m/min] / (π × D [mm])

Feed rate:

milling:            v_f = f_z × z × n
turning, drilling:  v_f = f × n

Metal removal rate:

milling:   Q = a_p × a_e × v_f
turning:   Q = v_c × f × a_p          (Q = 12 V f d in in³/min)
drilling:  Q = (π D² / 4) × v_f
  • v_c — cutting speed; D — diameter of the cutter, the drill or the workpiece being turned
  • f_z — chip load per tooth; z — number of teeth or flutes; f — feed per revolution
  • a_p — depth of cut; a_e — width of cut (radial engagement in milling)

Surface finish converter (Ra, RMS, Rz, N grades)

Conversions:

Ra [µin] = Ra [µm] × 39.37
Rq ≈ 1.11 × Ra          (sine profile: Rq/Ra = π / (2√2))
Rz ≈ 4 × Ra             (triangular profile)

Grade numbers (ISO 1302, previous edition):

N1 = 0.025 µm, N2 = 0.05, … N7 = 1.6, N8 = 3.2, N9 = 6.3 … N12 = 50 µm

Theoretical turning finish:

R_t = f² / (8 r)
Ra = f² / (18√3 r) ≈ 0.0321 f² / r
  • Ra — arithmetic mean roughness; Rq — root mean square roughness (RMS)
  • Rz — maximum height of the profile; R_t — peak-to-valley height of the ideal turned profile
  • f — feed per revolution; r — tool nose radius

Tap drill size calculator (metric and UNC/UNF)

Tap drill for a percentage of thread:

drill = D − 1.299 × P × %/100
inch:   drill = D − 0.01299 × % / TPI
metric: drill = D − % × P / 76.98

Thread percentage a drill gives:

% = (D − drill) / (1.299 × P) × 100

Basic dimensions (ISO 724, ASME B1.1):

pitch diameter   d2 = D − 0.649519 × P
minor diameter   D1 = D − 1.082532 × P
  • D — major (nominal) diameter; P — pitch, P = 1/TPI for inch threads
  • 100 % thread is a double thread depth of 1.299 P, so the basic minor diameter D1 is 83.3 % thread

Weld metal and filler consumption calculator

Weld cross-section without reinforcement:

fillet (equal legs):   A = z² / 2
single V:              A = g t + (t − f)² tan(α/2)
double V (symmetric):  A = g t + (t − f)² tan(α/2) / 2

Mass, filler and time:

m = A × (1 + r) × L × ρ
filler = m / E
wire length = filler / (ρ π d² / 4)
arc time = m / deposition rate
  • z — fillet leg; t — plate thickness; g — root gap; f — root face; α — included groove angle
  • r — reinforcement and convexity allowance; L — weld length; ρ — weld metal density, 7 850 kg/m³ for steel
  • E — deposition efficiency: 55 % SMAW, 95 % GMAW, 90 % FCAW, 100 % SAW (Kobe Steel)
  • d — wire diameter

Results are estimates. They do not replace the governing code, class or flag requirements, or a check by a competent person.