Skip to content
Engineering Bible

Results appear as you type. Use the arrow keys to move through them and Enter to open one.

Popular

↑ ↓ moveEnter openEsc close

Molarity calculator (moles, mass, volume, normality)

Molarity, mass of solute or volume of solution from the other two, with molar masses of common reagents, moles, normality, molality and % w/w.

Units
Leer en español

Results are estimates. They do not replace the governing code, class or flag requirements, or a check by a competent person. Report a problem

Introduction

Molarity is the number of moles of a solute per litre of solution, written mol/L or M. You calculate it by dividing the mass of solute by its molar mass, which gives the moles, and then by the volume of solution in litres. Dissolving 58.44 g of sodium chloride and making it up to 1 L gives a 1 M solution. Turned around, the same relation tells you how much to weigh out: 250 mL of 0.5 M NaCl needs 7.305 g.

This calculator solves for the mass of solute, the molarity or the volume of solution from the other two. It has the molar masses of 22 common reagents, or you can enter your own. It also gives the moles, the normality of acids and bases, and the molality and % w/w when you know the solution density. It is for laboratory technicians, chemistry students and process engineers preparing solutions.

Formulas

Molarity, moles and mass:

n = m / M
c = n / V
m = c × V × M

Normality, molality and mass fraction:

N = c × z
b = n / (ρ V − m)
w = m / (ρ V)
  • c — molarity, mol/L; n — moles of solute; V — volume of solution, L
  • m — mass of solute, g; M — molar mass, g/mol
  • z — equivalents per mole: 1 for HCl and NaOH, 2 for H₂SO₄, 3 for H₃PO₄
  • b — molality, mol per kg of solvent; ρ — solution density; w — mass fraction

Assumptions and limitations

  • The volume is the final volume of the solution. Dissolve the solute in less solvent, then make it up to the mark.
  • Hydrates include their water of crystallisation. CuSO₄·5H₂O weighs 249.68 g/mol, against 159.60 g/mol for the anhydrous salt.
  • Normality depends on the reaction. The table covers acid–base use; for redox, enter the electrons per mole, such as 5 for permanganate in acid.
  • Molality and % w/w need the measured density of the solution at its temperature.
  • The reagent is taken as pure. For a 98 % assay, divide the mass by 0.98.

Worked example

How much sodium chloride is needed for 250 mL of a 0.5 M solution?

  1. Volume: 250 mL = 0.250 L.
  2. Moles: 0.5 mol/L × 0.250 L = 0.125 mol.
  3. Molar mass of NaCl: 22.990 + 35.45 = 58.44 g/mol.
  4. Mass: 0.125 × 58.44 = 7.305 g.

Weigh 7.305 g of NaCl, dissolve it in about 200 mL of water, and make up to 250 mL in a volumetric flask.

Common cases

Mass of solute to weigh for one litre of common laboratory solutions, with molar masses from the IUPAC 2021 atomic weights. Dissolve it in less water and make up to the mark; for another volume, scale the mass in proportion.

CaseMolar mass, g/molMolarity, mol/LMass for 1 L (g)
Saline, 0.9 % w/v NaCl (0.154 M)58.4400.1548.9998
1 M sodium chloride58.440158.44
0.1 M sodium hydroxide39.9970.13.9997
1 M sodium hydroxide39.997139.997
3 M potassium chloride74.5483223.64
1 M Tris base121.1361121.14
0.5 M EDTA disodium dihydrate372.2380.5186.12
0.1 M silver nitrate169.8740.116.987
0.02 M potassium permanganate158.0320.023.1606
0.1 M copper(II) sulphate pentahydrate249.6770.124.968

Every row is worked out by this calculator each time the site is built, and checked for impossible values. Open a case to load its inputs.

Common mistakes

  • Adding the solute to a litre of water. Molarity is per litre of final solution. Dissolving the solute in 1 L of water gives more than 1 L of solution and a lower concentration. Dissolve it in less water and make up to the mark.
  • Weighing the anhydrous mass of a hydrate. For 1 L of 0.1 M copper sulphate from the pentahydrate on the shelf, weigh 24.97 g. Weighing the 15.96 g worked out from the anhydrous molar mass gives only 0.0639 M.
  • Confusing molarity with normality. Sulphuric acid gives two protons per molecule, so 0.5 M H₂SO₄ (49.04 g per litre) is 1 N. A method that asks for 1 N acid and gets 1 M has twice the acid it expects.
  • Confusing molarity with molality in strong solutions. 37 % hydrochloric acid of density 1.18 g/mL is 12.0 M but 16.1 mol/kg, because the litre of solution holds only about 743 g of water. The two agree only in dilute solutions.
  • Treating a weighed sodium hydroxide solution as exact. NaOH pellets take up water and carbon dioxide from the air, so the mass weighed holds less NaOH than it seems. Standardise the solution by titration before using it as a titrant.

FAQ

How do you calculate molarity?

Divide the moles of solute by the litres of solution. 10 g of glucose (180.16 g/mol) in 500 mL is 0.0555 mol / 0.5 L = 0.111 M.

What is the difference between molarity and molality?

Molarity is moles per litre of solution; molality is moles per kilogram of solvent. Molality does not change with temperature, because it uses masses only.

What is normality?

Molarity times the equivalents per mole for the reaction. 0.5 M sulphuric acid gives two protons per molecule, so it is 1.0 N.

How do I find the molarity of a concentrated acid?

Multiply the density by the mass fraction to get g/L, then divide by the molar mass. 37 % HCl of density 1.18 g/mL holds 437 g/L, which is 12.0 M.

How do I make a solution from a concentrated stock?

Use C1V1 = C2V2. To make 1 L of 1 M HCl from 12 M stock, take 83 mL of stock and make it up to 1 L, always adding acid to water.

Why does my solution not come out to the right concentration?

Common causes are a wet or hydrated salt, an impure reagent, making up to the wrong volume, or a temperature far from the flask's calibration.

Related calculators

What this calculator is checked against

Before every release the calculator must reproduce each case below. The note under each case says where the expected answer comes from: a standard, a textbook, a published table, or a hand calculation shown in full.

  1. 250 mL of 0.5 M NaCl: 0.125 mol, 7.305 g (29.22 g/L)Hand calculation: m = c V M with M(NaCl) = 58.44 g/mol
  2. Reagent HCl, 37.0 wt% with density 1.18 g/mL, is 12.0 M (molality 16.1 mol/kg)Harris, Quantitative Chemical Analysis, ch. 1: molarity of 37.0 wt% HCl from its density
  3. Molar masses agree with published values within 0.01 %: NaCl 58.44, NaOH 40.00, H₂SO₄ 98.08, glucose 180.16, KMnO₄ 158.03, CuSO₄·5H₂O 249.69IUPAC 2021 atomic weights; CRC Handbook formula weights
  4. Normality: 0.5 M H₂SO₄ is 1.0 N, 0.1 M H₃PO₄ is 0.3 N; a salt has no table normality unless equivalents are enteredAcid–base equivalents per mole (Harris ch. 1; IUPAC equivalent entity)
  5. Round trip: 10 g of glucose in 500 mL is 0.1110 M, and 10 g at that molarity fills 500 mLc = m / (M V) and V = m / (M c) by hand
  6. A density too low for the solute, zero volume and an unknown reagent are rejectedBehaviour check: warnings and rejected inputs
  7. Worked example of the article: the calculator reproduces 0.125, 7.305 g to the digits printedThe worked example on this page, to the digits printed

Assumptions and sources

Assumptions and limits

  • Molarity is moles of solute per litre of final solution (not per litre of solvent): dissolve the solute and then make up to the volume.
  • Molar masses are computed from the IUPAC 2021 abridged standard atomic weights; hydrates include their water, so weigh the form named on the bottle.
  • Normality uses the acid–base equivalents per mole in the table (H₂SO₄ 2, H₃PO₄ 3, Na₂CO₃ 2 to carbonic acid); redox and precipitation normalities differ and must be entered for the reaction.
  • Molality and % w/w need the density of the solution, which depends on the concentration and temperature; leave it at zero to skip them.
  • Purity is taken as 100 %; divide the mass by the assay fraction for a technical-grade reagent.

Sources

  • IUPAC Commission on Isotopic Abundances and Atomic Weights (CIAAW), Standard atomic weights 2021, abridged to five significant figures
  • Harris, D.C., Quantitative Chemical Analysis, 9th ed., W.H. Freeman, ch. 1 (molarity, molality and preparing solutions; molarity of 37.0 wt% HCl)
  • IUPAC Compendium of Chemical Terminology (Gold Book): amount concentration, molality, equivalent entity

Cite this calculator

Papandreou, C. (2026). Molarity calculator (moles, mass, volume, normality). Engineering Bible. https://engineeringbible.com/process/molarity/

Embed this calculator on your site

Copy this HTML into your page. The calculator stays free to use and links back here.

By Christos Papandreou. Updated . How the numbers are checked.