Skip to content
Engineering Bible

Results appear as you type. Use the arrow keys to move through them and Enter to open one.

Popular

↑ ↓ moveEnter openEsc close

Specific gravity calculator (SG, API gravity, Baumé)

Specific gravity of liquids from density, API gravity or Baumé degrees, and of gases from the molar mass, with density in kg/m³, lb/ft³ and lb/gal.

Units

Results are estimates. They do not replace the governing code, class or flag requirements, or a check by a competent person. Report a problem

Introduction

Specific gravity is the density of a substance divided by the density of a reference. For liquids the reference is water, so you calculate it as SG = ρ / ρ_water. A diesel of 850 kg/m³ has a specific gravity of 0.851 against water at 60 °F. For gases the reference is air, and the ratio of molar masses gives it: methane is 0.554. The oil industry also uses API gravity, and the chemical industry Baumé degrees, both of which are scales based on SG.

This calculator converts between density, specific gravity, API gravity and the heavy and light Baumé scales. It also gives a gas's specific gravity and its density at a chosen temperature and pressure. It is for process, petroleum and chemical engineers, and for anyone reading a hydrometer or a fuel certificate.

Formulas

Liquids, against water at the chosen reference:

SG = ρ / ρ_water          ρ_water = 999.016 kg/m³ at 60 °F, 999.972 kg/m³ at 4 °C

API gravity and Baumé degrees, on SG at 60/60 °F:

°API = 141.5 / SG − 131.5
°Bé (heavier than water) = 145 − 145 / SG
°Bé (lighter than water) = 140 / SG − 130

Gases, against dry air at the same temperature and pressure:

SG_gas = M / 28.964
ρ_gas = P M / (R T)
  • ρ — density; SG — specific gravity, no units
  • M — molar mass, g/mol; R = 8.314 J/(mol·K)
  • P — absolute pressure; T — absolute temperature

Assumptions and limitations

  • API gravity and Baumé degrees are defined at 60 °F. Enter the density at 60 °F (15.56 °C), or correct a measured density with the ASTM D1250 petroleum tables first.
  • The two water references differ by about 0.1 %. Petroleum work uses 60 °F; laboratory work often uses 4 °C. State which one a number uses.
  • The heavy Baumé scale is for acids, brines and syrups; the light scale is for oils, solvents and ammonia water. The US scales use the moduli 145 and 140.
  • Gas specific gravity assumes ideal gases. At high pressure the density also needs the compressibility factor Z.

Worked example

A crude oil assay reports 35 °API. What are its specific gravity, density and weight per gallon?

  1. Specific gravity at 60/60 °F: 141.5 / (35 + 131.5) = 0.8498.
  2. Density at 60 °F: 0.8498 × 999.016 = 849.0 kg/m³.
  3. Weight per US gallon: 849.0 × 0.0083454 = 7.09 lb/gal.
  4. On the light Baumé scale: 140 / 0.8498 − 130 = 34.7 °Bé.

This is a medium crude, lighter than water by 15 %.

Common cases

Typical densities of common liquids at about 15 °C, with specific gravity against water at 60 °F, API gravity and weight per US gallon. Fuels and crude oils vary from batch to batch; the delivery note has the real figure.

CaseDensity (kg/m³)SG 60/60 °F°APIlb per US gallon
Gasoline (petrol)7400.740759.536.176
Ethanol7890.789847.666.585
Jet fuel, kerosene8000.800845.206.676
Diesel8400.840836.797.010
Light crude oil8500.850834.817.094
Heavy crude oil9340.934919.857.795
Heavy fuel oil9850.986012.018.220
Fresh water9991.000010.008.337
Sea water1,0251.02606.418.554

Every row is worked out by this calculator each time the site is built, and checked for impossible values. Open a case to load its inputs.

Common mistakes

  • Forgetting the reference temperatures. SG at 60/60 °F and SG at 15/4 °C use different water densities and differ by about 0.1 %. Say which one a figure is.
  • Using a density at the wrong temperature. Fuel oils lose about 0.6 to 0.7 kg/m³ per °C as they warm. Correct to 15 °C before comparing with a specification.
  • Reading API gravity the wrong way round. API rises as the liquid gets lighter: water is 10 °API, light crude about 35, gasoline about 60.
  • Comparing a gas with water. Gas specific gravity is relative to air at the same temperature and pressure, not to water.
  • Mixing US and imperial gallons. An imperial gallon is 20 % larger than a US gallon, so pounds per gallon differ by the same amount.

FAQ

How do you calculate specific gravity?

Divide the density of the substance by the density of water at the reference temperature. Sea water at 1 025 kg/m³ has an SG of 1.026 against water at 60 °F.

How do I convert API gravity to specific gravity?

SG = 141.5 / (API + 131.5). A 10 °API oil has an SG of 1.000, the same as water, and a 40 °API oil an SG of 0.825.

What is a light or heavy crude oil?

By the usual industry convention, light crude is above about 31 °API and heavy crude below about 22 °API. Heavier crudes need more processing and fetch a lower price.

What is the Baumé scale?

A hydrometer scale for liquids. For liquids heavier than water, °Bé = 145 − 145 / SG, so 66 °Bé sulphuric acid has an SG of 1.835. For lighter liquids, °Bé = 140 / SG − 130.

What is the specific gravity of natural gas?

About 0.55 to 0.7 against air. Pure methane is 0.554; heavier hydrocarbons, nitrogen and CO₂ raise it.

Is specific gravity the same as density?

No. Density has units such as kg/m³ or g/cm³. Specific gravity has none, but it equals the density in g/cm³ to within about 0.1 % when water is the reference.

Related calculators

What this calculator is checked against

Before every release the calculator must reproduce each case below. The note under each case says where the expected answer comes from: a standard, a textbook, a published table, or a hand calculation shown in full.

  1. 35 °API: SG 60/60 °F = 141.5 / 166.5 = 0.84985, 849.01 kg/m³, 7.085 lb/US gal, 34.7 °Bé lightAPI MPMS Ch. 11.1 definition of API gravity; Baumé light 140/SG − 130 (ASTM E100); hand calculation
  2. Water at 60 °F is 10 °API, 0 °Bé heavy and 10 °Bé light; 10 °API round-trips to SG 1Definitions of the API and Baumé scales (the scales are anchored on water)
  3. 66 °Bé sulphuric acid has a specific gravity of 1.835 at 60/60 °FUS Baumé heavy scale SG = 145 / (145 − °Bé); 66 °Bé is the commercial grade of concentrated sulphuric acid, sold as SG 1.835
  4. Reference choice: 850 kg/m³ is SG 0.85084 against water at 60 °F and 0.85002 against water at 4 °CSG = ρ / ρ_water with ρ_water 999.016 (API MPMS 11.1) and 999.972 kg/m³ (CIPM 2001)
  5. Gases: air is 1, methane 0.554, propane 1.522; methane at 15 °C and 1 atm is 0.6785 kg/m³ (ideal gas)Gas SG = M / 28.964 (ISO 2533 air); IUPAC 2021 molar masses; ρ = P M / (R T) by hand
  6. Out-of-range entries are rejected and an implausible gravity warnsBehaviour check: warnings and rejected inputs
  7. Worked example of the article: the calculator reproduces 0.8498, 849.0 kg/m³, 7.09, 34.7 to the digits printedThe worked example on this page, to the digits printed

Assumptions and sources

Assumptions and limits

  • Liquid specific gravity is the density divided by that of water at the reference chosen: 999.016 kg/m³ at 60 °F (the petroleum convention, API MPMS Ch. 11.1) or 999.972 kg/m³ at 4 °C (the scientific convention); the two differ by 0.1 %.
  • API gravity and both Baumé scales are defined on the specific gravity at 60/60 °F, so a density entered for them must be the density at 60 °F (15.56 °C); correct a density measured at another temperature with the ASTM D1250 (API MPMS 11.1) tables first.
  • Baumé heavy (145 − 145/SG) applies to liquids denser than water and Baumé light (140/SG − 130) to lighter liquids, the US scales used in North American industry.
  • Gas specific gravity is the ratio of molar masses to dry air (28.964 g/mol), which equals the density ratio for ideal gases at the same temperature and pressure; the gas density uses the ideal gas law.

Sources

  • API Manual of Petroleum Measurement Standards Ch. 11.1 (ASTM D1250), and ASTM D287 / D1298: API gravity = 141.5 / SG(60/60 °F) − 131.5
  • ASTM E100, Standard Specification for ASTM Hydrometers (specific gravity, API and Baumé heavy and light scales at 60/60 °F)
  • Tanaka, M. et al. (2001), Recommended table for the density of water, Metrologia 38, 301–309 (CIPM water density)

Cite this calculator

Papandreou, C. (2026). Specific gravity calculator (SG, API gravity, Baumé). Engineering Bible. https://engineeringbible.com/process/specific-gravity/

Embed this calculator on your site

Copy this HTML into your page. The calculator stays free to use and links back here.

By Christos Papandreou. Updated . How the numbers are checked.