Skip to content
Engineering Bible

Results appear as you type. Use the arrow keys to move through them and Enter to open one.

Popular

↑ ↓ moveEnter openEsc close

Drag and lift force calculator

Aerodynamic drag or lift force from ½ρv²CA, the power to overcome drag, and air density from altitude and temperature, with typical Cd values.

Units

Results are estimates. They do not replace the governing code, class or flag requirements, or a check by a competent person. Report a problem

Introduction

Aerodynamic drag is the force the air exerts against a moving body. To calculate it, multiply the dynamic pressure, ½ ρ v², by the drag coefficient and the frontal area. Lift uses the same formula with the lift coefficient and the wing area. A car with a drag coefficient of 0.30 and 24 ft² of frontal area meets 90 lbf of drag at 70 mph, and needs about 17 hp just to push through the air.

This calculator gives the drag or lift force, the dynamic pressure and the power to overcome the drag. It finds the air density from the altitude and temperature, or takes it directly. It offers typical drag coefficients for cars, cyclists, flat plates and spheres. It is for car and bike enthusiasts, students, and drone and model builders.

Formulas

Dynamic pressure, force and power:

q = ½ ρ v²
F = q × C × A
P = F × v

Air density from altitude and temperature:

p = 101 325 × (1 − 2.25577 × 10⁻⁵ z)^5.2559    Pa
ρ = p / (287.04 × T)

Typical drag coefficients on frontal area:

BodyCdSource
Passenger car0.30Çengel and Cimbala
Cyclist, upright, about 0.5 m²1.1Munson et al.
Cyclist, racing crouch, about 0.36 m²0.88Munson et al.
Flat square plate or disc facing the flow1.17Hoerner
Sphere, laminar boundary layer0.47Hoerner
  • ρ — air density; v — air speed relative to the body
  • C — drag coefficient Cd or lift coefficient CL
  • A — frontal area for drag, wing area for lift
  • z — altitude in m; T — air temperature in K

Assumptions and limitations

  • The coefficient is held constant. In reality it changes with the Reynolds number, the yaw angle and, above about Mach 0.3, compressibility.
  • The speed is the speed through the air. Add a head wind to the road speed, or subtract a tail wind.
  • The power covers only the drag. Rolling resistance and drivetrain losses come on top.
  • Dry air is assumed. Humidity lowers the density slightly: saturated air at 30 °C is 1.6 % lighter than dry air.

Worked example

A car has a drag coefficient of 0.30 and a frontal area of 24 ft². How much drag does it meet at 70 mph at sea level on a 59 °F day, and what power does that take?

  1. Air density: 101 325 Pa / (287.04 × 288.15 K) = 1.225 kg/m³.
  2. Speed: 70 mph = 31.29 m/s.
  3. Dynamic pressure: ½ × 1.225 × 31.29² = 599.8 Pa, or 12.53 psf.
  4. Drag: 12.53 × 0.30 × 24 = 90.2 lbf.
  5. Power: 401.2 N × 31.29 m/s = 12.55 kW, or 16.84 hp.

At 80 mph the drag rises by (80 / 70)² to 118 lbf, and the power by (80 / 70)³ to 25 hp.

FAQ

How do I calculate drag force?

Multiply ½ × air density × speed squared by the drag coefficient and the frontal area. In US units, the dynamic pressure in psf is about 0.00256 × mph² at sea level.

What is a typical drag coefficient for a car?

About 0.30 for a passenger car. Values differ with the body shape, so use the maker's published figure when there is one.

How much power does aerodynamic drag take?

Drag force times speed. Because the force grows with speed squared, the power grows with speed cubed.

What is CdA?

The drag coefficient times the frontal area. It is the single number that sets the drag at a given speed and air density.

How does altitude affect drag?

Thinner air means less drag at the same speed. At 5 280 ft on a 30 °C day the density is 0.959 kg/m³, and the drag is 22 % lower than at sea level on a standard day.

How do I calculate lift?

Use the same formula with the lift coefficient and the wing area. In level flight the lift equals the weight.

Related calculators

What this calculator is checked against

Before every release the calculator must reproduce each case below. The note under each case says where the expected answer comes from: a standard, a textbook, a published table, or a hand calculation shown in full.

  1. Car, Cd 0.30 on 24 ft², 70 mph at sea level and 15 °C: q 599.8 Pa, drag 401.2 N (90.2 lbf), 16.84 hpHand calculation, F = ½ ρ v² Cd A with ρ = 1.2250 kg/m³ (ISA sea level)
  2. Drag power grows with the cube of speed: twice the speed needs eight times the powerP = ½ ρ v³ Cd A
  3. Racing cyclist, Cd 0.88 on 0.36 m², at 10 m/s in 1.225 kg/m³ air: 19.40 N and 194 WMunson, Young and Okiishi, typical drag coefficients (racing bicycle 0.88 on 0.36 m²); hand calculation
  4. Lift: CL 0.3 on a 16.2 m² wing at 60 m/s in 1.225 kg/m³ air is 10 716 N; no drag power for liftL = ½ ρ v² CL S
  5. At 5 280 ft and 30 °C the density is 0.9588 kg/m³ and the drag 21.7 % lower than the sea-level standardASHRAE standard pressure p = 101 325 (1 − 2.25577e−5 Z)^5.2559 and ρ = p / (287.042 T)
  6. A zero area, a negative coefficient and an unknown body are rejectedBehaviour check: warnings and rejected inputs
  7. Worked example of the article: the calculator reproduces 1.225 kg/m³, 12.53 psf, 90.2 lbf, 16.84 hp to the digits printedThe worked example on this page, to the digits printed

Assumptions and sources

Assumptions and limits

  • The force is F = ½ ρ v² C A with the coefficient referred to the area given: the frontal area for drag coefficients of cars, cyclists and bluff bodies, the wing planform area for lift coefficients.
  • The coefficient is taken as constant; real coefficients change with Reynolds number (a sphere drops from 0.47 to about 0.2 when its boundary layer turns turbulent), yaw angle and, near Mach 0.3 and above, compressibility.
  • The speed is the air speed relative to the body: for a car or cyclist in still air it is the road speed; add a head wind, subtract a tail wind.
  • Air density comes from the standard-atmosphere pressure at the altitude and the actual temperature for dry air, or can be entered directly; humidity lowers it slightly (saturated air at 30 °C is 1.6 % lighter than dry air).
  • The power is the drag force times the speed; the engine or rider must also supply rolling resistance and drivetrain losses, which are not included.

Sources

  • S.F. Hoerner, Fluid-Dynamic Drag, published by the author, 1965, Chapter 3 (flat plates and discs normal to the flow, C_D ≈ 1.17; sphere 0.47 subcritical)
  • Y.A. Çengel and J.M. Cimbala, Fluid Mechanics: Fundamentals and Applications, 4th ed., McGraw-Hill 2018, Table 11-2 (passenger car C_D ≈ 0.3)
  • B.R. Munson, D.F. Young and T.H. Okiishi, Fundamentals of Fluid Mechanics, Wiley, figure of typical drag coefficients (bicycle upright 1.1 on 0.5 m², racing 0.88 on 0.36 m²)
  • ASHRAE Handbook — Fundamentals, Chapter 1, eq. (3) standard atmospheric pressure, via the shared psychrometric module

Cite this calculator

Papandreou, C. (2026). Drag and lift force calculator. Engineering Bible. https://engineeringbible.com/automotive/drag-and-lift/

Embed this calculator on your site

Copy this HTML into your page. The calculator stays free to use and links back here.

By Christos Papandreou. Updated . How the numbers are checked.