Automotive and aerospace glossary
20 terms from the automotive and aerospace calculators, each in two or three sentences with its symbol, its unit and a typical value. Every entry links to the calculators that use it; the formula sheet has the equations.
-
Brake specific fuel consumptiong/kWh (lb/hp·h)
Also called BSFC
The mass of fuel an engine burns per unit of brake power output per hour, a direct measure of its efficiency. Naturally aspirated petrol engines run about 0.45 to 0.50 lb/hp·h, about 270 to 300 g/kWh, at full power; turbocharged tunes are sized at 0.60 to 0.65 for their richer mixtures. Injector sizing multiplies it by target power.
-
Calibrated airspeedkn (km/h)
Also called CAS, KCAS, indicated airspeed, IAS
Indicated airspeed corrected for errors of the pitot-static system and instrument installation, read from the aircraft handbook table. The correction is usually a few knots, largest at low speed and high angle of attack. True airspeed is found from it using pressure altitude and outside air temperature.
True airspeed calculator (TAS and Mach), Thrust-to-weight, wing loading and stall speed calculator
-
Compression ratiodimensionless
Also called CR, static compression ratio
The ratio of a cylinder’s total volume with the piston at bottom dead centre to its volume at top dead centre: (swept volume + clearance volume) ÷ clearance volume. Modern petrol engines run about 10:1 to 13:1 and diesels 14:1 to 20:1. A higher ratio raises efficiency but, in a petrol engine, also the risk of knock.
Compression ratio calculator, Engine displacement calculator
-
Density altitudeft (m)
Also called DA
The altitude in the International Standard Atmosphere at which the air density equals the actual density at a place. It rises about 120 ft for every 1 °C above the ISA temperature, so a field at 5000 ft pressure altitude and 30 °C sits near 8000 ft. Take-off run, climb and engine power follow it, not field elevation.
Density altitude calculator, True airspeed calculator (TAS and Mach), Thrust-to-weight, wing loading and stall speed calculator, Drag and lift force calculator
-
Drag coefficientCddimensionless
Also called Cd, drag factor, Cx
A number that relates drag force to dynamic pressure and a reference area: F_D = ½ × ρ × v² × C_d × A. Modern cars have about 0.25 to 0.35 on frontal area, a sphere about 0.47 in laminar flow and a flat plate or disc facing the flow about 1.17. Drag power rises with speed cubed.
-
Drivetrain loss%
Also called parasitic loss, wheel horsepower, crank horsepower
The share of engine power lost in the gearbox, differential, shafts and tyres between the crankshaft and the road. Chassis dynos typically show 10 % to 15 % for manual two-wheel-drive cars and 18 % to 25 % for automatics and all-wheel drive. Crank power is wheel power divided by (1 − loss).
Horsepower calculator, Quarter-mile ET and trap speed calculator
-
Engine displacementVdcm³ (L, in³)
Also called swept volume, engine capacity, cc, cubic inches
The total volume swept by all the pistons of an engine in one stroke each: π/4 × bore² × stroke × number of cylinders. A four-cylinder engine with 86 mm bore and 86 mm stroke displaces about 2.0 litres. It excludes the clearance volume above the pistons at top dead centre.
Engine displacement calculator, Compression ratio calculator, Engine BMEP, torque and power
-
Final drive ratiodimensionless
Also called axle ratio, differential ratio, rear-end ratio
The speed reduction between the gearbox output and the driven wheels, set by the crown wheel and pinion in the differential. Cars commonly use about 3.0:1 to 4.5:1. The overall ratio is gear ratio × final drive, and road speed is engine rpm × tyre circumference ÷ overall ratio.
Gear ratio and vehicle speed calculator, Tire size calculator and comparison, Gear ratio, rpm and torque
-
Horsepowerhphp (kW)
Also called hp, bhp, PS, brake horsepower
A unit of power, 745.7 W for mechanical horsepower and 735.5 W for metric horsepower, PS. From torque it is lbf·ft × rpm ÷ 5252, or in SI, kW = N·m × rpm ÷ 9549. Quoted figures are at the crankshaft unless stated as wheel horsepower.
Horsepower calculator, Quarter-mile ET and trap speed calculator, Fuel injector size calculator, Torque, power and speed
-
Lift coefficientCLdimensionless
Also called CL, CL_max
A number that relates lift force to dynamic pressure and wing area: L = ½ × ρ × v² × C_L × S. It rises roughly linearly with angle of attack, about 0.1 per degree for a wing section, to a maximum of 1.2 to 1.6 for a clean wing and above 2 with flaps, beyond which the wing stalls.
Drag and lift force calculator, Thrust-to-weight, wing loading and stall speed calculator
-
Mach numberMadimensionless
Also called Mach, speed of sound
The ratio of a body’s speed to the local speed of sound, which in air depends on temperature only: about 340 m/s, or 661 kn, at 15 °C and 295 m/s at −56.5 °C in the lower stratosphere. Compressibility becomes significant above about Mach 0.3, and airliners cruise near Mach 0.78 to 0.85.
Speed of sound and Mach number calculator, True airspeed calculator (TAS and Mach)
-
Power-to-weight ratiokW/t (hp/lb)
Also called power loading, weight-to-power ratio, hp per tonne
Engine power divided by vehicle or aircraft weight, the main predictor of acceleration and climb. A typical family car has about 60 to 100 kW per tonne and a sports car over 200; drag racers use the inverse, pounds per horsepower, to estimate quarter-mile times. Include driver and fuel in the weight.
Quarter-mile ET and trap speed calculator, Horsepower calculator, Thrust-to-weight, wing loading and stall speed calculator
-
Pressure altitudeft (m)
Also called PA, standard altitude, flight level
The altitude in the International Standard Atmosphere at which the standard pressure equals the actual pressure at a place, read on an altimeter set to 1013.25 hPa or 29.92 inHg. Near sea level each hectopascal below standard adds about 27 ft. It is the starting point for density altitude and true airspeed.
Density altitude calculator, True airspeed calculator (TAS and Mach), Thrust-to-weight, wing loading and stall speed calculator
-
Specific impulseIsps
Also called Isp, exhaust velocity, delta-v, rocket equation
The thrust a rocket engine produces per unit weight flow of propellant, in seconds, equal to effective exhaust velocity divided by standard gravity, 9.80665 m/s². Kerosene and oxygen engines reach about 300 to 350 s in vacuum, hydrogen and oxygen about 450 s. The rocket equation gives delta-v = Isp × g0 × ln(initial mass ÷ final mass).
-
Stall speedVSkn (m/s)
Also called Vs, Vs0, Vs1, stalling speed
The lowest steady flight speed at which a wing can produce lift equal to weight, reached at the maximum lift coefficient: √(2W ÷ (ρ × S × C_L,max)). A light training aircraft stalls at about 45 to 55 kn clean. It rises with the square root of load factor, about 41 % higher in a 60° banked turn.
Thrust-to-weight, wing loading and stall speed calculator, Drag and lift force calculator, Density altitude calculator
-
Stopping distancem (ft)
Also called braking distance, reaction distance, perception-reaction time
The distance a vehicle covers from the moment the driver sees a hazard to a standstill: reaction distance plus braking distance. Reaction distance is speed × perception-reaction time, 2.5 s in AASHTO design, and braking distance is v² ÷ (2 × μ × g). At 100 km/h on dry asphalt with μ = 0.75 braking alone takes about 52 m.
Stopping distance calculator, Vertical curve calculator (crest and sag)
-
Thrust-to-weight ratioT/Wdimensionless
Also called T/W, TWR
The ratio of engine thrust to vehicle weight, both as forces. Above 1 a vehicle can accelerate straight up: fighter aircraft reach about 1.1 at combat weight, airliners sit near 0.25 to 0.35 at take-off and rockets need about 1.2 to 1.5 at lift-off. It governs climb and acceleration.
Thrust-to-weight, wing loading and stall speed calculator, Rocket equation calculator (delta-v)
-
True airspeedkn (km/h)
Also called TAS, KTAS
The speed of an aircraft relative to the air mass it flies through. It exceeds calibrated airspeed by roughly 1.5 % to 2 % per 1000 ft, so 120 kn calibrated at 8000 ft in standard air is about 135 kn true. Navigation uses it with wind to find ground speed, while stall and structural limits follow calibrated airspeed.
True airspeed calculator (TAS and Mach), Speed of sound and Mach number calculator, Density altitude calculator
-
Tyre aspect ratio%
Also called tire aspect ratio, tire size, profile, sidewall ratio
The height of a tyre’s sidewall as a percentage of its section width, the middle number in a size such as 205/55 R16. That tyre has a 112.75 mm sidewall and an overall diameter of about 632 mm. Changing overall diameter by more than about 3 % upsets the speedometer and gearing.
Tire size calculator and comparison, Gear ratio and vehicle speed calculator
-
Wing loadingW/Skg/m² (lb/ft²)
Also called W/S
Aircraft weight divided by wing area. Light training aircraft have about 50 to 80 kg/m², or 10 to 16 lb/ft², and airliners 500 to 700 kg/m². A higher value gives a smoother ride in turbulence and faster cruise, but a higher stall speed and a longer take-off run.
Thrust-to-weight, wing loading and stall speed calculator, Drag and lift force calculator, Density altitude calculator
Results are estimates. They do not replace the governing code, class or flag requirements, or a check by a competent person.