Skip to content
Engineering Bible

Results appear as you type. Use the arrow keys to move through them and Enter to open one.

Popular

↑ ↓ moveEnter openEsc close

Fuel injector size calculator

Fuel injector size in lb/hr and cc/min from horsepower, BSFC, injector count and duty cycle, or the horsepower injectors support, with fuel pressure.

Units

Results are estimates. They do not replace the governing code, class or flag requirements, or a check by a competent person. Report a problem

Introduction

How big do fuel injectors need to be? Multiply the target horsepower by the brake specific fuel consumption to get the total fuel flow. Then divide by the number of injectors and by the maximum duty cycle. A 450 hp naturally aspirated V8 on gasoline needs eight injectors of about 35 lb/hr each, or about 370 cc/min.

This calculator sizes injectors in lb/hr and cc/min for gasoline or E85, naturally aspirated or boosted, and corrects for a fuel pressure different from the rating. It also works the other way, giving the horsepower a set of injectors supports. It is for engine builders and tuners planning an upgrade.

Formulas

Injector size and horsepower supported:

flow per injector = hp × BSFC / (n × DC)
hp = flow × n × DC / BSFC

Fuel pressure and units:

flow at p2 = flow at p1 × √(p2 / p1)
cc/min = lb/hr × 453.6 / 60 / ρ
  • hp — flywheel horsepower; BSFC — lb of fuel per hp per hour
  • n — number of injectors; DC — maximum duty cycle, such as 0.80
  • p — pressure across the injector, fuel pressure minus manifold pressure
  • ρ — fuel density in g/cm³: 0.72 for gasoline, which gives 10.5 cc/min per lb/hr, and 0.78 for E85

Typical BSFC values, lb/(hp·h):

EngineGasolineE85 (× 1.5)
Naturally aspirated0.45 to 0.500.75
Supercharged0.55 to 0.750.90
Turbocharged0.55 to 0.750.975

Assumptions and limitations

  • BSFC depends on the engine, the tune and the air-fuel ratio. Boosted engines run richer to control knock, so they use more fuel per horsepower.
  • E85 needs about 1.5 times the fuel mass of gasoline, because its stoichiometric air-fuel ratio is 9.8 instead of 14.7.
  • Injector makers generally suggest a duty cycle of 85 % at most. The default of 80 % leaves a margin.
  • Flow follows the pressure across the injector. With a 1:1 boost-referenced regulator that difference stays at the base pressure.
  • Diesel and direct-injection engines are sized differently. Enter a BSFC only if you have one from the engine builder.

Worked example

An engine builder plans a 450 hp naturally aspirated V8 on gasoline. It has eight injectors, and the maximum duty cycle is 80 %. The injectors are rated at 43.5 psi (3 bar) and will run at that pressure.

  1. Total fuel flow: 450 × 0.50 = 225.0 lb/h.
  2. Per injector: 225.0 / (8 × 0.80) = 35.2 lb/h.
  3. In cc/min: 35.16 × 453.6 / 60 / 0.72 = 369.1 cc/min.

Choose the next size up that is available, to leave a margin for a richer tune. Eight 42 lb/hr injectors would support 537.6 hp at the same duty cycle.

FAQ

How do I calculate injector size?

Multiply horsepower by BSFC, then divide by the number of injectors and the maximum duty cycle. The result is in lb/hr.

How do I convert lb/hr to cc/min?

Multiply by about 10.5 for gasoline. The exact factor is 453.6 / 60 divided by the fuel density in g/cm³.

What BSFC should I use?

About 0.50 for a naturally aspirated gasoline engine and 0.60 to 0.65 for a supercharged or turbo engine. For E85, multiply by 1.5.

How much horsepower will my injectors support?

Multiply the injector flow by the number of injectors and the duty cycle, then divide by BSFC. Eight 42 lb/hr injectors at 80 % support 537.6 hp at BSFC 0.50.

Does raising fuel pressure increase injector flow?

Yes, with the square root of the pressure. Going from 43.5 to 58 psi raises the flow by 15.5 %.

How much bigger do injectors need to be for E85?

About 50 % bigger by mass, because E85 needs 1.5 times as much fuel for the same air.

Related calculators

What this calculator is checked against

Before every release the calculator must reproduce each case below. The note under each case says where the expected answer comes from: a standard, a textbook, a published table, or a hand calculation shown in full.

  1. 450 hp NA gasoline (BSFC 0.50), 8 injectors at 80 %: 225 lb/hr in total, 35.2 lb/hr each, 369.1 cc/minEngineLabs (Acosta 2024): lb/hr = hp × BSFC / (injectors × duty cycle); hand calculation
  2. 650 hp at BSFC 0.50 on 8 injectors at 85 % needs 650 × 0.5 / 6.8 = 47.8 lb/hrSame formula; hand calculation
  3. Gasoline at 720 kg/m³: 1 lb/hr = 453.592 / 60 / 0.72 = 10.50 cc/min, the usual conversionUnit conversion; EN 228 density range 720 to 775 kg/m³
  4. Reverse: eight 42 lb/hr injectors at 80 % support 42 × 8 × 0.8 / 0.5 = 537.6 hp; at 58 psi instead of 43.5 psi, 620.8 hphp = flow × n × DC / BSFC; orifice flow ∝ √Δp
  5. E85 needs 14.7 / 9.8 = 1.5 times the gasoline flow: a turbo E85 engine uses BSFC 0.975Stoichiometric air-fuel ratios 14.7 (gasoline) and 9.8 (E85); Heywood Appendix D
  6. Fractional injectors, a 5 % duty cycle and an unknown fuel are rejected; 95 % duty warnsBehaviour check: warnings and rejected inputs
  7. Worked example of the article: the calculator reproduces 225.0 lb/h, 35.2 lb/h, 369.1 to the digits printedThe worked example on this page, to the digits printed

Assumptions and sources

Assumptions and limits

  • Fuel flow is the flywheel horsepower times the brake specific fuel consumption (BSFC); each injector delivers its share at no more than the maximum duty cycle, the fraction of each engine cycle it is open.
  • Typical gasoline BSFC: 0.45 to 0.50 lb/(hp·h) naturally aspirated and 0.55 to 0.75 with a supercharger or turbo, which run richer to control knock (EngineLabs); the presets use 0.50, 0.60 and 0.65.
  • E85 needs about 1.5 times the fuel mass of gasoline for the same air (stoichiometric air-fuel ratio 9.8 against 14.7), so its presets are the gasoline values × 1.5; methanol, diesel or other fuels need a BSFC from the engine builder.
  • Injector flow rises with the square root of the pressure across the injector (fuel pressure minus manifold pressure), as for any orifice; on a boosted engine with a 1:1 regulator the difference stays at the base pressure.
  • lb/hr converts to cc/min with the fuel density: 720 kg/m³ for gasoline, which gives the usual 10.5 cc/min per lb/hr (EN 228 allows 720 to 775 kg/m³), and 780 kg/m³ for E85.

Sources

  • G. Acosta, How To Calculate What Size Fuel Injectors Your Engine Needs, EngineLabs, 21 June 2024 (lb/hr = hp × BSFC / (injectors × duty cycle); BSFC 0.45–0.50 NA, 0.55–0.75 forced induction; maximum duty cycle about 85 %)
  • J.B. Heywood, Internal Combustion Engine Fundamentals, McGraw-Hill 1988, Section 2.9 (brake specific fuel consumption) and Appendix D (stoichiometric air-fuel ratios)
  • EN 228 Automotive fuels — Unleaded petrol — Requirements and test methods (density at 15 °C 720.0 to 775.0 kg/m³)

Cite this calculator

Papandreou, C. (2026). Fuel injector size calculator. Engineering Bible. https://engineeringbible.com/automotive/fuel-injector-size/

Embed this calculator on your site

Copy this HTML into your page. The calculator stays free to use and links back here.

By Christos Papandreou. Updated . How the numbers are checked.