Skip to content
Engineering Bible

Results appear as you type. Use the arrow keys to move through them and Enter to open one.

Popular

↑ ↓ moveEnter openEsc close

Horsepower calculator

Horsepower from torque and rpm, or estimated from quarter-mile time or trap speed and weight, in hp, kW and PS, at the crank and the wheels.

Units
Leer en español

Results are estimates. They do not replace the governing code, class or flag requirements, or a check by a competent person. Report a problem

Introduction

Horsepower is the rate at which an engine does work. To calculate it from a dyno reading, multiply the torque in lbf·ft by the rpm and divide by 5 252. An engine making 400 lbf·ft at 5 000 rpm produces 380.8 hp. Without a dyno, drag racers estimate power from the car's weight and its quarter-mile time or trap speed.

This calculator gives the crank horsepower from torque and rpm, or estimates it from a time slip with three published sets of constants. It shows the result in hp, kW and PS, and the wheel horsepower after a drivetrain loss. It is for car enthusiasts reading dyno sheets and time slips, and for anyone converting between horsepower units.

Formulas

Power from torque, exact:

P = T × 2π × N / 60
hp = T[lbf·ft] × N[rpm] / 5 252

Estimates from a quarter-mile run:

hp = W × (K_t / ET)³
hp = W × (mph / K_v)³

Wheel and crank power:

hp_wheel = hp_crank × (1 − loss)
  • T — torque; N — engine speed
  • W — race weight in lb, with driver and fuel
  • ET — elapsed time in s; mph — trap speed
  • K_t, K_v — Hale 5.825 and 234; Fox 6.050 and 225; Huntington 6.290 and 224
  • 1 hp = 745.7 W; 1 PS = 735.5 W

Assumptions and limitations

  • Power from torque and rpm is exact. Torque and horsepower curves always cross at 5 252 rpm when plotted in lbf·ft and hp.
  • The time-slip formulas are estimates fitted to drag-strip results. They give flywheel horsepower for a car with good traction on a prepared track.
  • Trap speed is the better guide. A poor launch or wheelspin adds tenths to the elapsed time but changes the trap speed much less.
  • The drivetrain loss is an assumption. 15 % is a common figure for a manual rear-drive car, and automatics and all-wheel drive lose more.
  • The constants differ because they were fitted to different cars. Hale's suit modern performance cars; Huntington's came from 1960s muscle cars.

Worked example

An engine dyno shows 400 lbf·ft at 5 000 rpm. What is the power at that point, and at the wheels with a 15 % drivetrain loss?

  1. Power: 400 × 5 000 / 5 252 = 380.8 hp.
  2. In kilowatts: 380.8 × 0.7457 = 284.0 kW.
  3. In metric horsepower: 284 000 / 735.5 = 386.1 PS.
  4. At the wheels: 380.8 × (1 − 0.15) = 323.7 hp.

In a 3 500 lb car with good traction, the Hale formula predicts a trap speed of 234 × (380.8 / 3 500)^(1/3) = 111.7 mph. Working backwards from a time slip, 111.7 mph gives back about 381 hp.

Common cases

Crank horsepower from the torque at one engine speed, and the wheel horsepower after a 15 % drivetrain loss. The torque and rpm are typical points for each kind of engine, not the figures of any one model.

CaseTorque (lbf·ft)Engine speed (rpm)Crank power (hp)Crank power (kW)Wheel power (hp)
Small garden engine153,0008.5686.38917.2828
Small petrol four-cylinder1005,500104.7278.0989.012
Turbo four-cylinder at peak torque2502,00095.270.9980.92
Sport motorcycle near the redline8011,000167.55124.94142.42
Diesel pickup at peak torque7501,800257.04191.67218.48
Pickup V8 at peak power4005,000380.8283.96323.68
Sports-car engine at high rpm3507,000466.48347.85396.51
Heavy truck diesel at peak torque1,5001,200342.72255.57291.31

Every row is worked out by this calculator each time the site is built, and checked for impossible values. Open a case to load its inputs.

Common mistakes

  • Using 5 252 with torque in N·m. The constant 5 252 works only with lbf·ft. With N·m use kW = N·m × rpm / 9 549: 400 N·m at 5 000 rpm is 209.4 kW, or 280.9 hp, not the 380.8 hp that 400 lbf·ft gives.
  • Multiplying peak torque by the peak-power rpm. Torque and rpm must come from the same point on the curve. A turbo engine making 250 lbf·ft at 2 000 rpm produces 95.2 hp there. Multiplying that torque by 5 500 rpm gives 261.8 hp, which the engine reaches only if its torque holds all the way up.
  • Comparing wheel horsepower with a rated crank figure. Ratings are quoted at the crank, and a chassis dyno reads at the wheels. With a 15 % loss, 323.7 hp at the wheels is the same engine as 380.8 hp at the crank, so the engine is not down on power.
  • Leaving the driver out of the race weight. The quarter-mile formulas use the weight as the car sits on the line, with driver and fuel. A car trapping 113.6 mph is estimated at 400.5 hp at 3 500 lb, but at 377.6 hp if a 200 lb driver is left out.
  • Treating hp and PS as the same unit. Metric horsepower is about 1.4 % smaller than mechanical horsepower, so 380.8 hp is 386.1 PS. A rating in PS reads higher than the same power in hp, and one in kW reads lower.

FAQ

How do I calculate horsepower from torque?

Multiply torque in lbf·ft by rpm and divide by 5 252. In SI units, kW = N·m × rpm / 9 549.

Why do torque and horsepower cross at 5 252 rpm?

Because 5 252 is the constant in hp = lbf·ft × rpm / 5 252. At that speed the two numbers are equal.

How accurate is horsepower from a quarter-mile time?

It is an estimate. For the same elapsed time, Huntington's constant gives 26 % more power than Hale's, so the choice of constants matters. Trap speed gives a more reliable figure than elapsed time.

What is the difference between hp and PS?

PS is metric horsepower, 735.5 W. One mechanical horsepower is 745.7 W, so 100 hp is 101.4 PS.

What is wheel horsepower?

The power a chassis dyno measures at the driven wheels. It is lower than crank power because the gearbox, driveshaft and differential absorb some of it.

How do I convert hp to kW?

Multiply by 0.7457. A 300 hp engine is 224 kW.

Related calculators

What this calculator is checked against

Before every release the calculator must reproduce each case below. The note under each case says where the expected answer comes from: a standard, a textbook, a published table, or a hand calculation shown in full.

  1. 400 lbf·ft at 5 000 rpm is 400 × 5 000 / 5 252.1 = 380.8 hp, 284.0 kW, 386.1 PS; 323.7 hp at the wheels with 15 % lossP = T ω with 1 hp = 550 ft·lbf/s (33 000 / 2π = 5 252.11); 1 PS = 735.49875 W
  2. Torque and horsepower cross at 5 252 rpm: 300 lbf·ft there is 300 hphp = lbf·ft × rpm / 5 252 (definition of the mechanical horsepower)
  3. Chassis dyno: 300 hp at the wheels with a 15 % loss is 352.9 hp at the crankWheel = crank × (1 − loss)
  4. Hale constants: 3 500 lb trapping 113.6 mph is 400.5 hp; the same car at 12.00 s is 400.3 hpMcCaul 2014, Table 2: Patrick Hale / Quarter Jr. K_t = 5.825, K_v = 234.0; hp = W (mph/K_v)³ = W (K_t/ET)³
  5. 1970 AAR ’Cuda (3 585 lb, 14.30 s, rated 290 hp): Huntington’s ET formula gives 305.1 hp, within 6 % of the ratingMcCaul 2014, test data of the AAR ’Cuda and Huntington constants K_t = 6.29, K_v = 224
  6. Zero torque, a 70 % loss and an unknown formula are rejectedBehaviour check: warnings and rejected inputs
  7. Worked example of the article: the calculator reproduces 380.8 hp, 284.0 kW, 386.1 PS, 323.7 hp to the digits printedThe worked example on this page, to the digits printed

Assumptions and sources

Assumptions and limits

  • Power from torque is exact: P = T × 2π × rpm / 60, which is hp = lbf·ft × rpm / 5 252 with 1 hp = 550 ft·lbf/s; torque and horsepower curves therefore cross at 5 252 rpm.
  • The elapsed-time and trap-speed formulas are empirical estimates from drag-strip data: hp = W (K_t / ET)³ and hp = W (mph / K_v)³ with the race weight W in lb (car, driver and fuel). They give engine (flywheel) horsepower, as the Wallace Racing calculator that uses the same form states.
  • Trap speed estimates power better than elapsed time, because the launch, traction and shifting affect the ET far more than the speed at the end of the run.
  • Wheel horsepower is crank horsepower times (1 − drivetrain loss); the loss is an assumption, often taken as 15 % for a manual rear-drive car and higher for automatics and all-wheel drive.
  • kW and PS (metric horsepower, 75 kgf·m/s = 735.5 W) are the same power in other units; 1 hp (mechanical) = 745.7 W.

Sources

  • SAE J1349 (2011) Engine Power Test Code — Spark Ignition and Compression Ignition — As Installed Net Power Rating (power from measured torque and speed)
  • E.L. McCaul, The ET & MPH Equations, June 2014, Table 2 Some published empirical ET and MPH equations (Hale 5.825/234.0; G. Fox 6.050/225.0; Huntington 6.290/224.0)
  • Wallace Racing, ET-MPH-HP calculator (wallaceracing.com/et-hp-mph.php): weight as the car sits on the line with driver and fuel, horsepower at the flywheel

Cite this calculator

Papandreou, C. (2026). Horsepower calculator. Engineering Bible. https://engineeringbible.com/automotive/horsepower/

Embed this calculator on your site

Copy this HTML into your page. The calculator stays free to use and links back here.

By Christos Papandreou. Updated . How the numbers are checked.