Skip to content
Engineering Bible

Results appear as you type. Use the arrow keys to move through them and Enter to open one.

Popular

↑ ↓ moveEnter openEsc close

Density altitude calculator

Pressure altitude from field elevation and altimeter setting, and density altitude from temperature and dew point, with the ISA formula and the rule of thumb.

Units

Results are estimates. They do not replace the governing code, class or flag requirements, or a check by a competent person. Report a problem

Introduction

Density altitude is the height in the standard atmosphere where the air has the same density as the air around you. It is pressure altitude corrected for a non-standard temperature. Aircraft wings, propellers and engines respond to density, so a hot day at a high airport makes an aircraft perform as if it were much higher. A 5 000 ft airport at 30 °C has a density altitude of about 7 600 ft.

This calculator finds the station pressure and the pressure altitude from the field elevation and the altimeter setting. It then gives the density altitude from the outside air temperature with the standard atmosphere formula, and optionally with humidity from the dew point. The 120 ft per °C rule of thumb is shown alongside. It is for pilots checking take-off and climb performance, and for drone, car and engine tuners who correct for air density.

Formulas

Station pressure and pressure altitude, ISA troposphere:

p = QNH × (1 − L h / T0)^5.2559
PA = (T0 / L) × (1 − (p / p0)^0.190263)

Density and density altitude:

ρ = p / (R T_v)
T_v = T / (1 − (e / p)(1 − 0.622))
DA = (T0 / L) × (1 − (ρ / ρ0)^0.234969)

Rule of thumb for comparison:

DA ≈ PA + 120 ft × (OAT − T_ISA)
T_ISA = 15 °C − 1.98 °C × PA / 1 000 ft
  • QNH — altimeter setting; h — field elevation
  • T0 = 288.15 K, p0 = 1 013.25 hPa (29.92 inHg), ρ0 = 1.225 kg/m³, L = 6.5 K/km
  • R = 287.05 J/(kg·K); T — outside air temperature in K
  • e — vapour pressure at the dew point; T_v — virtual temperature

Assumptions and limitations

  • The formulas cover the troposphere, below 36 089 ft. That includes every airport and most piston-aircraft flying.
  • The altimeter setting is the station pressure reduced to sea level through the standard atmosphere. The calculator reverses that step to find the station pressure.
  • Pilots usually leave humidity out. Moist air is lighter than dry air, so humidity raises the density altitude by a few hundred feet on a warm, humid day.
  • The 120 ft per °C rule is an approximation. In the worked example it overestimates the exact result by about 180 ft.

Worked example

An airport sits at 5 000 ft. The altimeter setting is 30.10 inHg and the temperature is 30 °C. What are the pressure and density altitudes?

  1. Station pressure: 30.10 × (1 − 0.0065 × 1 524 / 288.15)^5.2559 = 25.04 inHg.
  2. Pressure altitude: the standard atmosphere has 25.04 inHg at 4 841 ft.
  3. Standard temperature there: 15 − 1.98 × 4.841 = 5.4 °C, so the air is 24.6 °C warmer than standard.
  4. Density: 84 811 Pa / (287.05 × 303.15 K) = 0.9746 kg/m³.
  5. Density altitude: the standard atmosphere has that density at 7 608 ft.
  6. Rule of thumb: 4 841 + 120 × 24.59 = 7 792 ft.

With a dew point of 15 °C the density altitude rises to 7 855 ft. The aircraft will perform as if it were taking off from about 7 600 to 7 900 ft.

FAQ

What is density altitude?

The pressure altitude corrected for a non-standard temperature. It is the standard-atmosphere height with the same air density.

How do I calculate pressure altitude?

Set the altimeter to 29.92 inHg and read it. Without that, a quick estimate is the field elevation plus (29.92 − altimeter setting) × 1 000 ft.

How do I calculate density altitude?

Find the air density from the station pressure and temperature, then find the standard-atmosphere height with that density. The rule of thumb adds 120 ft for each °C above the standard temperature.

Does humidity affect density altitude?

Yes. Water vapour is lighter than air, so humid air is less dense. The FAA advises adding 10 % to the computed take-off distance when humidity is high.

Why does density altitude matter?

High density altitude lengthens the take-off run, reduces the climb rate and raises the true airspeed on approach. A normally aspirated engine also loses power.

What is the standard temperature at altitude?

15 °C at sea level, falling about 1.98 °C per 1 000 ft. At 10 000 ft it is −4.8 °C.

Related calculators

What this calculator is checked against

Before every release the calculator must reproduce each case below. The note under each case says where the expected answer comes from: a standard, a textbook, a published table, or a hand calculation shown in full.

  1. Standard day at sea level (29.92 inHg, 15 °C): pressure and density altitude 0 ft, density 1.2250 kg/m³ICAO Doc 7488/3, sea-level values (101 325 Pa, 288.15 K, 1.2250 kg/m³)
  2. ISA at 10 000 ft: station pressure 696.82 hPa (20.58 inHg), σ = 0.73848, density altitude 10 000 ftICAO Doc 7488/3 table at 3 048 m: 696.82 hPa, 268.34 K, σ 0.73848
  3. Field 1 165 ft, altimeter 30.10 inHg: pressure altitude 1 001 ft, matching the NWS formula (1 − (p/1013.25)^0.190284) × 145 366.45NOAA/NWS pressure altitude formula; FAA rule (29.92 − 30.10) × 1 000 + 1 165 = 985 ft for comparison
  4. Hot day: 5 000 ft, 30.10 inHg, 30 °C gives 7 608 ft; the 120 ft/°C rule gives 7 792 ft, within 3 %Hand calculation from the ISA relations; rule of thumb DA ≈ PA + 120 (OAT − ISA)
  5. A 15 °C dew point raises the virtual temperature to 32.3 °C and the density altitude to 7 855 ftT_v = T / (1 − (e/p)(1 − ε)), Wallace and Hobbs Section 3.1; e from Hyland–Wexler (shared psychrometrics)
  6. A dew point above the temperature and an altimeter setting of 25 inHg are rejectedBehaviour check: warnings and rejected inputs
  7. Worked example of the article: the calculator reproduces 25.04 inHg, 4 841 ft, 5.4 °C, 7 608 ft, 7 792 ft, 0.9746 kg/m³ to the digits printedThe worked example on this page, to the digits printed

Assumptions and sources

Assumptions and limits

  • The atmosphere below the tropopause (36 089 ft, 11 km) follows the ICAO standard atmosphere: 15 °C and 1 013.25 hPa (29.92 inHg) at sea level, a lapse rate of 1.98 °C per 1 000 ft, dry-air gas constant 287.053 J/(kg·K).
  • The altimeter setting is QNH: the station pressure reduced to sea level through the standard atmosphere, so the station pressure is recovered with the same relation; the small instrument-height correction of US weather stations is ignored.
  • Pressure altitude is the standard-atmosphere height with the station pressure; density altitude is the standard-atmosphere height with the actual air density.
  • Humidity lowers the density through the virtual temperature T_v = T / (1 − (e/p)(1 − 0.622)), with e the saturation vapour pressure at the dew point (Hyland–Wexler, as in ASHRAE).
  • The rule of thumb DA ≈ PA + 120 ft × (OAT − ISA temperature) is shown for comparison; it ignores humidity and drifts from the exact value at high altitude and large temperature deviations.

Sources

  • ICAO Doc 7488/3, Manual of the ICAO Standard Atmosphere (extended to 80 km), 3rd ed. 1993 (troposphere relations and tables: 10 000 ft = 696.82 hPa, −4.81 °C, σ = 0.73848)
  • FAA-P-8740-2, Density Altitude (FAA Aviation Safety Program, 2008): pressure altitude with the altimeter at 29.92 inHg; density altitude is pressure altitude corrected for nonstandard temperature
  • J.M. Wallace and P.V. Hobbs, Atmospheric Science: An Introductory Survey, 2nd ed., Academic Press 2006, Section 3.1 (virtual temperature)

Cite this calculator

Papandreou, C. (2026). Density altitude calculator. Engineering Bible. https://engineeringbible.com/automotive/density-altitude/

Embed this calculator on your site

Copy this HTML into your page. The calculator stays free to use and links back here.

By Christos Papandreou. Updated . How the numbers are checked.